When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi !
I need to develop a BLE communication link between a smartphone (Android first, iOS after) and the BL654 Laird platform (based on nRF52840).
I found multiples strategies...
i am developing a bike power meter and designed my own hardware.
From software point of view I used the Ant+ bikepowermeter example from Nordic.
So far my status is, ...
To the kind attention of Nordic support team,
Could you please help me finding documentation about the subject I mentioned?
Let's suppose we have got a peripheral and...
Hello,
I am working on ble_app_uart example on nRF52840DK.
I am using one switch (gpio) for advertising_switch() function. It means on changing the position of the switch...
Hi,
Would you please tell me how can I dump a memory and save into a file in keil uVersion 5.24?
For example: I want to read the flash memory 0x00000000 to 0x00010000...
There is an option to 'Clone device's services':
A message pops up briefly to say that it's done it:
But it doesn't say where it's put it, and I can't see any...
Dear all,
I have picked the Ruuvi project : https://github.com/ruuvi/ruuvi.firmware.c and change the configuration to adapt with nordic dongle.
But after flashing, my...
Hi,
I am evaluating LC example, I am using an occupancy sensor. So whenever there's an occupancy it's detecting and turning the lights ON. But even when there's occupancy...
Hi,
I have created an eclipse based makefile project for nrf51802 module.
The sdk version that i am using is 12.3.0, and softdevice S130 .
Taking reference of ble_app_uart...
HW setup is my boart connected to a windows10 PC with an uart link.
I tried secure_bootloader_pca10100_uart_ses_nRF5SDKThreadv4.1.0.zip example, with some modification for...
Hi All,
I followed this article and got eclipse to work. I can use debugger, single-step, place a breakpoint. All good.
I noticed that disassembly window shows opcodes...
Hello,
I am working on a project that uses Azure as a cloud IoT provider and the NRF9160 as a gateway-like device which is supposed to make simultaneous connections to up...
Hi,
Just wondering if it is possible to configure the UICR Customer registers after erasing and flashing/programming the nrf52832. The hex file used to program the device...
Hi Team,
I wonder the operating system which has been ported on nRF52840 DK, I found multiple IoT OS what nRF52840 supports like ARM mbed, Zephyr, Contiki, etc. But can...
Using NCS 1.3.1.
Why is nrfx_spim_xfer() asserting when using NRFX_SPIM_FLAG_HOLD_XFER flag and a ss_pin ?
When not using a ss_pin in the spi config but configuring with...
