When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I need to stream data from NUS UART Central Device to one peripheral, but the device always disconnects while trying to send second set of data. So I changed the write_req...
Dear
I have changed light_switch server example of " nrf5_SDK_for_Mesh_v4.0.0_src" from PCA10056 to PCA10059. All function of the code works well except button.
For button...
Morning. I have a Fanstel840F module. I use attached example sketch. I flash nrf52DK with this sketch, it works fine. I can scan with NRF PC and Mobile software, and see smartTag1003...
Hi,
May i know any software utility suggestion to debug the USB data (200 bytes data) communication from device to host and vice versa for nRF52840.
Similar USB sniffer...
I think there is a bug in the west tool. If only one -Dxxxx=”xx.h" parameter in the command-line, the quotes will be filtered. So update the "nrfxlib\nrf_security\src\mbedtls...
Hello, everyone!
I am using nRF52DK and SDK v17, and I am dealing with the example of ble_app_uart.
Using this example, I am testing how buttons control BLE scanning...
Hello. I am trying to implement a application jump from my normal firmware located at memory 0x19000 per recommendations based on the soft device used (s112) to a different...
Hello,
I am working on the nrf9160 board using cloud client sample. The connection to AWS and the boards loses after running for a while. When I reset the board it connects...
Hi,
I'm super rookie on BLE project,
my question is how can I using button press to accept a central pairing instead of typing passkey,
here's my code, using nrf 52810...
Hello!
We are trying to send MQTT messages to a hosted mosquito broker via AT commands using the nRF9160.
We are trying to avoid programming the nrf9160 chip, as we...
SAADC resolution is set to 8 bits, channel is configured as single ended. Is it correct to say that SAADC digital output should be between 0x0000 and 0x00FF(full scale)? ...
Hi,
I'm testing the ble_app_uart example on the nRF52840 DK and it seems to be consuming a lot of current similar to the case in https://devzone.nordicsemi.com/f/nordic...
In a single core BLE SOC, whenever a BLE event occurs the BLE stack takes high priority and any application code running on the single core, is delayed while the event is...
Hi ,
I need to store strings in flash and came across the NVS. I referred to the example in samples/subsys/nvs and was able to do the nvs operation.
The following are...
Hey, so I was under the belief that the maximum size of data one can include in a BLE packet is 20 bytes (23 bytes total, 3 bytes overhead, so 20 total for custom data). With...
