I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I was asked by Nordic tech support to create a new ticket, because ticket number 357092 had become a long a winding thread.
I need a simple utility I can offer to an end...
I am developing a project using nRF5340 to drive some peripherals. During debugging, I found that no matter how I executed the pull-up/pull-down commands, the p1.00 and p1...
I am using qt C++ to refactor the dfu master station, currently I have a problem, that is, I want to communicate with 52840 simulated com but failed, I initialize, you see...
When I click ACTIONS/Build to build, the executable module(merged.hex) is not created. Now that zephyr/zephyr.elf has been created, the process will finish.
[Environ] nRF...
Hi,
I wanted to characterise the CS accuracy by changing the default parameters in
I get errors when I try to change rtt_type to sounding sequence. I tried both 32 and...
My customer Penguin ID has the following question about HCI USB for the nRF54LM20A. He claims this is only on the old Zephyr stack and not on the new one. Can you please comment...
Hello,
I'm doing some experimentation with nRF54L15DK dev kit.
I connected PPK2 to P6 on the board to measure VDD:nRF current consumed.
The DK is loaded with a release...
I’m working on an nRF5340 project (NCS 2.9.2) with simultaneous multi-image DFU using MCUboot, MCUmgr (SMP over BLE), and external flash (MX25R64, like the DK).
App-core...
Hi
I am moving an application to nRF54L15DK.
SDK is v3.2.2, single core only, no sysbuild.
Whenever I try to debug I get:
-- west flash: using runner nrfutil -- runners...
Hi,
i am developing under NCS 3.2.1.
I would like to if there exist a stand-alone command for creating DFU (nrfutil sub-command or similar) instead of https://github.com...
Hi guys, I have been working with a custom PCB based around the nRF5340 that uses the nPM1100 as the PMIC. I have configured it for 1V8 VOUTB output, fixed VBUS, VTERM high...
Hello, in the design reference it explicitly mentions:
“Important note on C9: The grounding of the C9 capacitor MUST be isolated from ALL ground layers except the bottom...
Hello,
I’ve been using SSD1306 128x64 OLED displays with nRF52840 boards for several years without any issues, building with nRF Connect SDK 2.5.x to 3.1.0. Recently, I...
We have thousands of devices live in production and we sometimes encounter the situation that we cannot restart bluetooth advertising anymore after a connection attempt. ...
Hi, we are investigating some devices in field, and have limited logs to work with. From time to time, we see EMM reports with cause 255. According to nRF9160 AT Commands...
