Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi,
I'm trying to run the i2s output sample from NRF Connect SDK 2.7.0 on the nrf52840 DK, and I'm only getting the clock signal from P1.15, and no signal from any of the...
I'm just a bit fuzzy on how all of the bootloader stuff comes together.
Our application is small (100K-ish), so a dual-bank strategy seems appropriate.
It uses a proprietary...
Hi.
Could you please tell me how to trigger an interrupt when changing the USBREGSTATUS register?
I can monitor the state of this register in polling mode, but I don't...
We used two different packages of 833 and assembled two batches of PCBs. The first batch used the aQFN package, and the radio can operate normally. The second batch used the...
Hi,
We are using nrf Connect SDK v2.0.2 with the hci_rpmsg app programmed into the network core. We have a second radio test DTM application programmed into the network...
Hi, I have used nrf5_SDK//examples/ble_peripheral/ble_app_hids_keyboard & ble_app_hids_mouse both examples with my nrf52840-DK this device is visible in my mobile and laptop...
Hi,
I have a custom nRF9160 board. ADXL362 & MX25R64 share the same SPI bus. I'm trying to validate it individually and looks like there is no communication between both...
Hi.
Board : nRF52840 DK
SDK : NCS 2.0.0 (zephyr) or SDK 17.1.0
I test qdec example.
if I set sampleper value 256us/128us, NRF_QDEC_EVENT_SAMPLERDY Event is not raised...
I am recently trying to get up and running with the nrf9160-DK and have been unable to flash the board successfully even with the Quick start (v0.2.6) app in nrf Connect....
I wanted to try getting all 3 outputs on my nRF5340DK. I tried following the instructions here - https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/security/tfm.html#manual_connection_to_virtual_com_ports_on_the_nrf5340_dk...
Hi,
We've developed a custom PCB featuring the nRF52840 Core Chip, but we're encountering significant challenges with antenna performance, resulting in poor range during...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
Hi,
1. Can nRF52840 run RCP+BLE at the same time? 2. Are there any examples you can provide to customers? 3. Are FLASH and RAM sufficient for resources?
Thank you for...
Hi,
Currently, I am working on ble_app_bps code and I alter it to be act as a beacon code and I can able to store a data in the flash memory area 0x30000 and it works fine...
FreeRTOS Kernel V10.0.0 MCU: nRF52840 SDK 17.1.0
Our device is fully functional, and we are currently performing various tests. During long-term testing, we found that...
