Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi,
I am using ble_sdk_app_hids_keyboard example:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_hids_keyboard.html...
Hello, I lived in Taiwan and I followed nRF9160 DK Getting Started and met a problem at establishing connection with nRF Cloud with my board.
The previous steps are all...
Hello, I'm trying to run C++ code on the nrf52832 but I'm getting an Hard Fault when sending a floating point to an ostream, like in "std::cout << 13.5f;". The FPU is enabled...
Hi All,
I'm trying to interface a SD Card with nRF52840 DK.
I've got a SD Card socket and a FAT32 formatted 8GB sd card.
When I run, fatfs example , I get following...
hello,
i am using nrf52840 in our customised board with sdk 15.2 and trying to achieve long range with coded phy using long range demo example as base now i could be able...
Hi,
I have two boards NRF52840 DK and I wanted to use example for BLE Central&Peripheral NRF Relay. I have just run example with Heart Rate peripheral and I can see that...
Hi there,
When I program my nrf24le1 in Keil uVision, I notice that when I load the program to the flash memory of the connected motherboard6700 with the nrf24 radio module...
I have downloaded the Kiel and uVision file (the nrf Probe) found here: https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF24-series and have gone through...
Hi,
I am using Keil 5 (downloaded with this link: https://www.keil.com/demo/eval/c51.htm ) and have downloaded the nrfProbe to this file. This is being used to program...
Hi, I am try to implement UART SERIAL Bootloader for my device and I just need to perform DFU using uart serial
I have tested the code and bootloader. My query is
Without...
When I run the "ble_app_blinky_pca10040_s132" example from SDK 17.0.2 and 15.2.0, right after Connected I'm seeing that device is Disconnected from device.
I tried with...
We need to programatically (on the Raspberry Pi using Python) send and receive characters to and from a smartphone using a custom service over BTLE. I have used the blinky...
I am trying to communicate with my IOT using wired uart serial port. I am using 840(MCU) (with softdevice #113).
code:
My Issue: Each time I am trying to run it while...
Hi,
I am trying to reduce the consumption of my Thingy91 device in idle mode. I am working with NCSv1.3 and the example asset_tracker. I am currently registering 0.60mA...
