When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello,
We have seen the below error,
NRF_ERROR_INVALID_ADDR If the EasyDMA is used and memory adress in not in RAM.
While trying to connect with an external sensor hub...
Timer A with a 10-minute interval, timer B with a 4-hour interval, and timer C with a 10-second interval are required, and A and B should also run out of time in low power...
Are there any updates on coded phy support for the nRF sniffer?
I found a thread about this from "over a year ago" which says to check back in 4-5 weeks: https://devzone...
When CENTRAL connects how can I read the UUID and ADDR of the peer?
static void ble_evt_handler(ble_evt_t const * p_ble_evt, void * p_context) {
switch (p_ble_evt->header...
Hi Team,
We are facing issue with Flash storage Handlers with ble handlers. When we add the fstorage to my application ble adversing is stopped suddenly.
We are having...
Hey,
I want to use a standard 16bit service and to add some custome characteristics to it, will this create any compliance issues? Is it complying to BLE specifications...
Hi all,
I'm using the "ble_beacon_app" example from the SDK 16.0.0 with the nRF52840 DK. I would like to change the TX power level.
In main.c function, I tried to change...
Hi All,
We tried to modify the Android source core of nRFTools for our Proximity application . And we used some nRF52832 and nRF52840 as the proximity device.
1) We connected...
Greetings,
we are developing a custom board that holds a nrf9160 chip. We have uart lines out on pins 28 and 29, as on the DK. We need to use the AT client in order to flash...
I've implemented a Application and Bootloader. I have the Bootloader set to Buttonless. However when I try to transition from the Application to Bootloader via:
/* Sets...
Nordic team:
We are developing a proprietary application for Android tablets using the Android-BLE-Library and have been experiencing issues with scanning after a long period...
Hello
I'm very new with nRF modules and currently struggling with BL652-SA-01-T/R module to run Bluetooth.
I have developed small pcb to test this module, PCB includes...
Good day,
I am using the ANNA-B112 BLE device from ublox in a custom design. The ANNA-B112 interfaces with a host MCU over UART. The ANNA=B112 is flashed with Soft Device...
Hello I have an application which requires the use of both BLE and Openthread in the same time. The BLE is meant to connect an OpenThread mesh network to a smartphone.
I...
Hi, I am trying to create a project using make in addition to my SES project. My problem is that I see no printouts on /dev/ttyACM0 (using minicom to debug this), but I do...
