I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello Nordic,
I have a sparkfun nRF52840 mini and I want to know which project from nRF5_SDK_15.3.0_59ac345 should I use to have my nRF52840 slave in the TWI communcation...
I am currently working from an SDK16.0 peripheral example utilising freeRTOS and polling the softdevice (NRF_SDH_DISPATCH_MODEL == 2).
This has worked fine for nRF5 SDK...
I have some problems with the TWI (I2C) and it seems that TWI1 does not send anything. I have managed to create a simple example to recreate the issue. I am using TWI1 instead...
Hello.
Is it possible to send more than 1B data via blinky characteristic from central to peripheral? I made my project with two characteristic (my own 128-bit UUID) basing...
I am using android ble with kotlin. I ported the Blinky example to kotlin. There is a reference escaped in object construction when on construction the BLEManager invokes...
Dear Nordic Team!
I am verifying my tools chain for nrf52840 Mesh project development by mesh light-switch example. I have 4 PCA10056 and make them to 1 provisioner, 1 client...
Hi,
I use sdk16 and nRF52832.I want to change advertising in the air:
Now I'm using the timer to change the adv.But I want to change adv with RF interrupt.
Like this...
I developed an application (BLE named Adriano) using nRF52840 DK, nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730, starting from ble_zigbee_dynamic example. I added some custom...
Hi,
I'm developping an application for nRF52840 as a BLE central. It is supposed to connect to an Android device (BLE peripheral) using a bond (encrypted connection with...
Hi everyone,
I went through the source code by Vidar Berg for background dfu using SDK 15.3. I am working with nRF52832 , S132 and SDk 12 with Keil IDE. I did try with secure...
Hi,
I am currently developing with nRF52811 chip using nRF52840 DK. Where can I find a reference 2.4GHz PCB antenna design document?
Thanks.
Regards,
Jxq
Dear Team:
Hi team,I just want to know:
1.Can the ESB protocol call the frequency hopping of Gazell? Is there a corresponding description and source code?
2.Can the...
hi, i am facing this unknown error at "unknown function at 0x000008C8",
i am doing a development project with nrf52832(sdk14.2 and s132v5,ble nus is used) mcu and sim800...
Hello, I'm developing SAADC on nRF52832.
While developing, I have problems now.
I applied sine wave on ADC input.
And the result is displayed on the figure that I...
Hi:
Use the nordic official nRF52832 development board , The software is SDK15.3(example: ble_app_uart ),
Find that there will be a continuous reset. What is the problem...
