Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
We are developping an application using an NRF52840, Based on nRF5 SDK for Thread and Zigbee V3.0.0
Running S140 softdevice
We are using BLE advertizements and Openthread...
I have a custom board with nRF52840 and uses Segger EDE.
In our project we would like to store some info about production to flash memory (DeviceID, production date etc...
I followed the guide Configuring and performing DFU over Mesh ,old firmware was examples\dfu\build\dfu_nrf52832_xxAA_s132_6.1.1_Debug\dfu_nrf52832_xxAA_s132_6.1.1.hex,new...
Hello,
I want am use NRF2401L01 for sending data wirelessly from one device to another device and vise-versa.
The First device is arduino nano(Transmitter) which senses...
I looked at the following question
nrRF2 GATT attribute read callback
and it does not quite answer what I want to know.
What I need to know is do I get signaled by the...
I have followed the getting started, with my new nRF52840DK, with switches at:
Sw6 Default
Sw8 On
VDD selected
when plugged into the USB, LED 5 blinks rapidly, LED...
Hello.
In order to connect multiple units on the previous question page ( https://devzone.nordicsemi.com/f/nordic-q-a/51970/implementing-multilinks-on-multiroll-programs...
I want to develop our PC software to control the USB nRF52840 Dongle to be as a BLE central device，so I need to know the command that the nRF Connect used to do this，but I...
HI as i am new to nrf nordic semiconductor development i have some quetsions regarding application im developing
I am trying to develop Ble application where nRF 52 will...
Hi,
I am trying to add DFU service in ble_beacon example. I am using SDK14 and softdevice is S132_5.0.0 for 52-dk.
I have merged dfu example with ble_beacon and initiate...
Hi,
For my application using softdevice I need ADC update every 400ms and Battery level update every 2sec and string update for HT1632 led driver every 2sec.So I have created...
Starting with the BLE Uart Service example code, I wanted to send longer length packets, so the necessitated modifying settings like NRF_SDH_BLE_GATT_MAX_MTU_SIZE, NRF_SDH_BLE_GAP_DATA_LENGTH...
I can power nrf52832 using USB without any issues.
I see a strange behaviour using external 3.3V adapters. The chip does not turn on. The power supply to the chip is available...
Hi,
I am working with relay example .I want my android to send data to the relay board .In which function of the relay example should I make the changes or will i need to...
