Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
I am running the light_switch example and it works fine works fine , I am using the nrf_application to configure the nodes.
I am using latest mesh sdk and 15.3 nrf sdk....
Hi guys
I had to integrate a CLI module into a project I'm working on, that is running FreeRTOS
after quite a lot of work, I managed to get this working, but seeing...
HI,
I am using nrf52832 dk. I have a sensor that gives a negative voltage. I want to measure the value using saadc.
and can I use differential mode saadc for negative...
Hello All,
I am working on the N51822 custom board.
Using segger IDE, SDK 12.3
Previously i have worked on the sdk 14.3 on the n52810 board. It is working properly...
Hello
I am using pin 1.15 of nrf52840 dongle with transistor with enable pin of another chip. The other chip is a wifi chip which I only want to switch on whenever I have...
Hi All
I am using nRF9160 DK version 0.8.5, and I have gone through this link, downloaded and Installed all the steps, given there. All seems to be running good.
But some...
Hi I am using the custom_bluetooth_service tutorial from https://github.com/bjornspockeli/custom_ble_service_example with SDK v15 and nrf52840 DK.
I am now trying to use...
Win10 + Segger embedded studio
I can get the pca10059 blinky example to work. ( C:\nRF5_SDK_15.3.0_59ac345\examples\peripheral\blinky )
I use the NRF connect Programmer...
We are trying to receive high speed data using UART. Currently our source is set to transmit an 8 byte packet once every second.
I have initialised the serial port in IRQ...
Is there a public bug-tracker available (even better: publicly hosted repository)? I'm currently trying to wrap the SDK in way suitable for our internal processes (CMake,...
Hi,
i'm using "cycling speed and cadence" on DK to make a test run. However, my bicycle-watch(base on ANT) doesn't receive any "ANT signal".
Searching in the devzone,...
On the picture channel 2 connected to reset button on PDK.
UART channel drops to GND 4ms after button pressed.
How to prevent this?
Tried this: https://devzone.nordicsemi...
Hello,
at 3.3V the current consumption of my development kit is about 21.5 µA.
Due to the law of energy conservation, I would expect the current at 1.8V to be a little...
Hi,
i'm not getting any signal with a fresh DK and the latest modem driver.
entering AT+COPS=? will make it unresponsive forever. (nordic LTE Link monitor times...
