Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi.
I'm using the arm_sin_f32 function to generate an array of sine wave values. However when this function gets called the softdevice crashes.
I've included:
#include...
I've been trying to chase down some of the engineering samples of the nRF52840 for a prototype with no success from distributors here in Japan (have tried Digikey and Mouser...
Hello,
I know that the NRF_TEMP peripheral is a restricted peripheral and should be accessed with the sd_temp_get function when the soft device is running. Heck I even...
Does the NFC library globally disable interrupts at any point? We're trying to track down an issue where our code occasionally misses an I2C event during NFC read/write.
Hi all,
when I try to send 6 bytes of 0xFF, the last bytes change. I use SPI in mode 3. I use the NRF52832 on a custom board using SDK13 with sd v4. See the following screengrab...
Keil4 compiler in the compiler C and assembly of the mixed code, the error content is: Branch offset 0x00000388 out of range of 16-bit Thumb branch, but offset encodable in...
This function contains a lot of tags that need to jump, but at compile time there are these errors.
this is ARM compilation and C mixed,How should this error be handled?...
Hello, I am trying to develop on the NRF52. I have the development board and have been spending time with the SDK and documentation. I understand how the GPIO should work...
Our nRF51822, S110 device uses concurrent advertising (iBeacons) when connected to the central. Our customer would like to have a variable tx power on the advertising packets...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hello
I adapted the ble_app_uart with twi functionality.
Therefore I included the "app_twi.h" which includes the "nrf_drv_twi.h"
But as visible in the picture, the "nrf_drv_twi...
Hi,
I'm using nrf51822 with soft device s130 version 1.0 and I'm trying to flash hex file of size 108kb from both keil u vision/nrfgo studio.
Flashing is success but application...
Hi
I probably have done multiple or bad inicialization of flash memory in code
and my MiniBeacon ( www.alibaba.com/.../Nordic-bluetooth-nRF51822-logo-customizable-minibeacon_60408141084...
hi..I am using nRF52832 with sd 132 v4.0.2, I want to store data received over BLE in flash. So i wanted to know how much is the memory available to store data in following...
