Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi,
I wanted to know whether Bluetooth 5.0 will ever be supported on the NRF51 series chips or we need to migrate from NRF51 to NRF52 in order to have Bluetooth 5.0 in...
hi,I have a issue about pairing.
anyone can tell me the process of pairing and binding ,how the event BLE_GAP_EVT_SEC_PARAMS_REQUEST generate;
Do you have same example about...
Hello,
I am developing a board, with nrf51422-qfaa chip. To match the antenna I'm using the BAL-NRF01D3 balun. I currently have problems with antenna not working and I'm...
I am running an appliction with S132 soft device, build on top of SDK 12.0.0. Problem is that the application sometimes stops running for ten seconds, or even more, when Bluetooth...
Hi all,
may be you can advice me on a solution.
I need to be able to wake up a system when one of the pins shows more than 1v and I also need to wake up system when...
Hi,
I'm using ble_app_multilink_central to connect different device.In the example, it can connect to the lbs service. If I want it connect the uart service,such as ble_app_uart...
Hi Nordic,
we need to modify bootloader code base on your dfu example. Now We meet a problem that we can't program it by clicking icon "Load" on keil comile project. report...
I am having problem to download SDK NRF51 12.0 example firmware onto Redbearlab BLE Nano nrf51822. The compilation and build is fine. It is shown as
Erased Failed!
Error...
I have a custom board with an nRF51822, running the ble_app_hrs from the 12.1.0 SDK with softdevice s130, using the internal RC clock in a custom_board.h as follows:
#define...
I'm learning about the nRF52 series and so far love everything I see, especially the SDK. But I just got to the point where I'd like to generate precisely timed output, and...
Hello Nordic Team,
As I'm worrying about the max payload lengh that I can notify using soft device s130.1.0.0 on nrf51822 (256 Kb Flash/ 16KB RAM, SDK10), I thought about...
Hi,
I'm porting our project from sdk10 to sdk12 with SD S132 V3.0.0. I cannot find a way to reset the device in app and boot in bootloader in order to do a OTA update....
I have a working custom DFU bootloader based on the official bootloader from the SDK 8.1.0.
Updating the normal application code works without any problem.
Now I want to...
Hello all,
I try to trigger two events with two different periods, the first at 200ms, the second at 300ms. When I set the same period for the compared value, it works...
Hello,
I am tring to do a Bootloader update OTA using the bootlader DFU Dual Bank. Application update OTA is working fine while it is not the case for Bootloader update...
