Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hello,
Is there a way to find out the currently used connection interval when configured as a server?
I only found the function sd_ble_gap_ppcp_get which provides the...
Hi,
I have created two proprietary characteristics with notification property to notify some data's using these two characteristics when some event occurs. I can able to...
Dear developer zone,
I am using nRF51822 with soft device and SDK 4.4.2
My device return an error on disconnection when the ble_bondmngr_bonded_masters_store function...
Hello,
I want to test my circuit using a CR2032 coin cell. Is there any way to jumper a coin cell into the supply on the nRF6310 and bypass the voltage regulator/RS232...
Hi,
I am curious what is the main difference between nRF8001 and nRF8002.One is for connectivity and the other is for proximity. However, I would like to develop an application...
i need a help with the attenna design. here is the eagle files, i'm not sure it is fine. i used a Balun BAL-NRF01D3 and my board thickness is 0.6mm. i need to know the copper...
I got the nRF51822 DK and tried hooking up the dongle. I am using Windows 7 32 bit. When I plugged the dongle into a USB port, there is a “JLinkCDCUARTPort（COM19)” added to...
Hi,
My device is always in bootloader mode, even if i flash the sample heart rate application it is not entering into the application. Actually, before it was working fine...
Hello,
I am planning to develop an application in which I need to do some image processing (probably using open CV libraries), and I would like to know if the nRF51822...
I see in the example code there is
#define FLASH_PAGE_SYS_ATTR (BLE_FLASH_PAGE_END - 3) /**< Flash page used for bond manager system attribute information. */
#define...
I'm using NRF51822 and I have some question about the ble connection:
according to BLE 4.0 spec, when Tsup(connection supervision time) reaches, connection lost is considered...
Hi
Do the latest sample apps (for example, Heart Rate) which do not required bonding behave as follows:-
make connection from iphone
enable notification
check...
We have done some test on how fast we can receive data from a BLE service, which is around 6KB/sec and this is all fine. This test was fairly easy to make, as we could just...
I have implemented my own I2C driver and I am getting issues with NACKs.
On review my code is doing what twi_hw_master.c is doing.
I then went looking for a Nordic sample...
