Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
For connecting an external TCXO reference, we need to know the specification for the slew rate and levels (Vhigh/Vlow). In the product specs, the clock accuracy is defined...
Hello. I'm newbie with the NCS environment so tell me if I'm saying nosense. I use the nrf connect extension in vs code ide. (SDK: v2.7.0 toolchain: v2.7.0)
I want to...
I am working on new project setup. I have copied a sample blinky project from nRF connect SDK(C:\ncs\v2.7.0\zephyr\samples\basic\blinky) and board I selected in Build configuration...
Hi,
I'm following this "Getting started with Nordic's Secure DFU bootloader, a step by step guide" ( https://devzone.nordicsemi.com/guides/short-range-guides/b/software...
In our application build with SDK 2.7.0 on a NRF52840 chip, we get an assert if we update the TX_Power for the connections.
If the bluetooth has made connection, we update...
Hey everyone!
I’m working on a project using Zephyr with an nRF5340 board and trying to configure UART1 completely from scratch. Most tutorials I’ve found only cover UART0...
Dear Nordic Support Team,
I am working with the nRF52840 and need to configure the SPI peripheral in Zephyr to operate without DMA.
I’ve encountered a few problems:
...
I am able to update the app core successfully from an external flash partition via the `mcumgr` desktop tool. However, this is not working for the net core.
It successfully...
I would like to create a thread based sensor and use Apple/Amazon/Google smarthome hubs as the OTBR. How do I commission a thread device (not a matter device) to these hubs...
Hello,
I'm working with Zephyr and using MCUBOOT as bootloader.
Due to HW design I have to set and hold a gpio as fast as possible when the application boots (to prevent...
Hello,
We're seeing an error that only happens after a cold reboot (unplugging the battery and replugging it) and it happens inside the bootloader while trying to open the...
Dear all:
I used this command to build light switch for 5340DK:
west build -p always --build-dir nrf/samples/matter/light_switch/build -b nrf5340dk_nrf5340_cpuapp nrf...
Kconfig failed: [Errno 22] Invalid argument: 'c:/users/user/zephyr/kconfig"' is an error that appeared this morning. What is supposed to be in the Kconfig file. I have been...
I can't remember where I found it now, there was a file somewhere that listed all the files in a project. It had
absolute paths which filled me with dread as it means a...
Hi
I am working on a custom board and have hit an issue with the software part. When the nrf_modem_lib_init function is invoked, it always ends with a timeout (errno ...
