Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
where can i find some simple examples that transmit / receivfe packets using the RADIO....
assume for the moment that i'll be implementing my own proprietary protocol atop...
Hello, I am trying to develop a 1000 Hz wireless gaming mouse. The mouse has a NRF52832 onboard and the dongle has a NRF52820 on it. (Cannot switch to 52840) I do know about...
Hello,
We have a custom PCB that includes an nRF9160 and nRF7000. We’re planning a hardware update to add external flash memory and would like to know if we can use the...
I'm currently working on a matter application on a custom board in NCS 2.9.0. In the documentation for the ipc_radio net core image the README at nrf/applications/ipc_radio...
Hi all,
I am trying to configure the NFC Pins for usage in an SPI application. However they do not even work for a simple nrf_gpio_pin_set after configuring them with nrf_gpio_cfg_output...
Hi
I have developed a PCB that will be used to control some sensors. The pins NFC1 and NFC2 are intended to be used as GPIOs. However, the default processor settings configure...
Are there any ways/workarounds/configurations to drive P0.9 on nrf52840 as an Input/Output instead of just being NFC pin.
Technically we should be able to drive this pin...
Hi,
I'm using an ISP2053 (nrf5340) chip on a custom board and debugging using the nrf5340dk. I'd like to use P0.02, P0.03 as part of an SPI bus.
I set up a simple experiment...
Hello everyone,
I've recently migrated a code from nRF51822 to nRF52832, thus I started using fds library to manage flash storage from SDK v17.1.
The issue I'm having...
So i have a custom nrf52840 board that i'm working on with SDK 15.2
I want to use the NFC as GPIO.
According to the docs i need to set in the sdk_config.h CONFIG_NFCT_PINS_AS_GPIOS...
Hi,
I'm developing an Android app that will be used on Samsung Galaxy Tab devices only in which the user can connect, through BLE, to another device, which is a module added...
Hi
We have a product that uses a nRF5x Soc. Is acts as both a central and peripheral. The central part connects to a pulseoxymeter, and the peripheral part allows an app...
Dear Developers,
I am in the process of implementing the nRF9151 and would like to inquire about the necessity of the blind vias in its pad. Like on the nRF9151-DK.
Are...
SDK: nRF Connect SDK 2.9.0 with VS Code
SoC: nRF52840. nRF52840-DK for development.
We are currently using USB to output logs for debugging. For production, we disable...
Hello, I am following the official tutorial ( academy.nordicsemi.com/.../) to enable DFU over USB function on both nrf5340DK and thingy53. I am using sysbuild for both board...
