I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
I recently switched from 52832 development using IAR to 52833 development using SES. As a result, I downloaded all new versions of the SDK, softdevice and, of course, SES...
There is a marked improvement in the handling of TrustZone in nrfjprog 10.11.0 and 10.12.00, but it seems it's still not quite all the way there. I can do:
and am able...
Hello,
I am developing DFU over a custom IEEE802.15.4 Protocol in our own embedded OS. I managed to write the new Firmware starting at bank1_start address. Now I need to...
Hello,
I am using nRF connect SDK v1.4.99-dev1. I have imported ZigBee light_bulb, light_switch,network_coordinator project in SEGGER and successfully created
the Zigbee...
-I was following this link- " devzone.nordicsemi.com/.../" and installed SEGGER JLink.
(all on Ubuntu)
-Installed gcc-arm and changed the tool chain path on Makefile.posix...
I try DTM using the serialized application . The serialized application interface is UART.
The software on Connectivity board is ble_connectivity in nRF5 SDK , it is not...
nRF52832 and SDK 17.0.2
Using the Examples/crypto/nrf_crypto/aes/aes_all_cli example I am getting the wrong output in CFB mode.
"example key_size 256_bit"
"example aes...
I am working on nRF51-DK with nRF51422 with softdevice S130 and SDK 12.3.0.
I see that GPIOTE driver provides sensing for signal transitions like NRF_GPIOTE_POLARITY_LOTOHI...
Hi,
I have setup the Segger Embedded Studio for ARM (Nordic Edition) V5.10d, and managed to compile a sample app from ,
V1.4.2 -> nrf -> samples -> bluetooth -> peripheral...
Hello,
I have different behaviour with 2 identical boards.
They behave differently (at least for BLE functions).
With jlink interface, I saved the flash binary of...
I have installed the toolchain according to nRF Connect guideline, on my MAC OSX.
My option settings are listed in the attached image.
I downloaded release 1.4.2.
...
Hi Sir
We are developing a product with nRF5340,
Now we faced the PCB layout symbol creation issue,
I can't find any information about footprint of nRF5340,
Can someone...
Hello,
I am trying to get acquire the accelerometer data every 4 hours for a sample duration of 60secs. These data are stored in RAM and on ble connection with the mobile...
Hi,
I'm totally new to programming nRF DK's.
What am I using?
Segger Embbedded Studio for ARM (Nordic Edition)
Toolchain: nRF Connect SDK v1.4.99-dev1
The "mqtt...
Hello there,
Since we use the lower level modules from Nordic's SDK for Mesh 4.2.0 - namely timeslot.c, bearer_handler.c and some additional modules to make them work properly...
