When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
My aim is on button press in peripheral side ,it should do advertise and sent data from single peripheral to multiple central(total two central).
I am using nrf52810...
Hi,
I am using nRF52840 SoC as a thread device in my application. I want to push data from sensors to cloud. So I need to configure one of my thread devices as border...
Hi Dev team,
I had an issue regarding getting the real time using RTC. I tried to follow the below dev zone blog but the CAL_RTC does not work in my code.
As such, I am...
To the kind attention of Nordic support team,
We are doing EMC pre-tests of our products using your nRF52833 .
At this stage, nRF52833 device is triggering itself a...
Hello.
I am following this tutorial, but unfortunately I am stuck at step 7. I am not sure which characteristic corresponds to the UART RX characteristic value.
I tried...
I've started an asset tracking project at the company that I work at and have tried to use the nrf9160 dev kit for the device tracking part.
I have updated the board firmware...
Hello -
We are working with the nRF52840 and SDK v17.0.0 and tuning our power consumption during System ON sleep. We understand how to wakeup the device using the RTC and...
Hi,
I have encounter a problem that the first button release event is missing if the key is pressed while powering up.
The SDK I am using is nRF5_SDK_17.0.0_9d13099. ...
Hi!
We are using nRF52832-QFAB (B0 variant) in one of our projects, and it works fine and well.
We are now in the process of using the nRF52832-QFAB-E0 in the same build...
how can I work it use nRF5 SDK 17.0.0? On https://developer.nordicsemi.com/nRF5_SDK/pieces/nRF_DeviceFamilyPack/ the newest pack is
NordicSemiconductor.nRF_DeviceFamilyPack...
Hi Support Team,
An error occurs when generating a signed binary file for central_dfu_smp.
Error: Header padding was not requested and image does not start with zeros...
Hello everyone
I success in compilation gpio basic example but I have some problem about bluetooth mesh example.
It show message "undefined reference to `bt_rpmsg_platform_init...
Hello!
I've only used the DK board so far, so I've rarely used an external debugger.
I'm going to use a custom board later, so I'd like to learn more about how to use...
I just both the board, and I can get the 4 LEDs and the NFC to work; I have followed all the instructions but unsure what is going on - and suggestions?
1.nrf9160 module abnormal reset, no abnormal reset log information, I would like to get modem related log submitted to you for further analysis, but I do not know how to use...
