I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I want to set up a SPI transfer so the transfer itself is triggered by PPI. The PPI is set up working, the chain of events is
Timer CC0 -> Set CS low
Timer CC1 -> Start...
In implementing the --application-version-string with nrfutil I found the help was inconsistent with the application.
The help for this option is:
In the example 2.7...
Hi guys.
I'm trying to merge two projects ble_app_beacon and nrf_crypto_aes_cbc_with_padding.
I used nrf_crypto_aes_cbc_with_padding as base, copied it to another folder...
hi
i want to develop a keyboard that can communicate whith pc by ble and 2.4g . now,the 2.4g's communicate between nrf52840 and nrf24lu1p is achieved by project gzp_desktop_emulator...
I am based in Hong Kong. I purchased NB-IoT sim card with "Three".
When using LTE Link Monitor, (with at_client) I can connect to the NB_IoT network, as Three support told...
Hi! I would like to power the DK through a external power bank. This leads to led5 blinking rapidly for a while and then turning off. I assume this is because of the debugger...
Hi Team,
We are trying to compile the code with my changes, that changes are normal changes only.
But we are getting below errors in "nrf52840.h" . But we didn't do...
I have a nrf51-DK, SDK 9.0, S110, dual-bank bootloader that supports both serial and ble protocols, developed using GCC/Eclipse. I'm able to flash my app/bootloader/softdevice...
We are building a sollution using nRF52832. Using the UART over BLE application example as a base we managed to add DFU capabilities to the application etc.
Right now I...
Dear NRF community and support This is a followup question to the DevZone post https://devzone.nordicsemi.com/f/nordic-q-a/2860/flashing-bootloader-and-application-via-j-link...
From everything I know and understand of the system architecture, this shouldn't be possible, but one of our early production units out in the fields has twice now apparently...
I'm designing a two-part computer input device: Part A will communicate with the computer over BLE, but it must also be able to forward along messages from Part B. Here's...
Hi,
I am trying to update the MTU between the central and peripheral to the maximum MTU.
at the connection interrupt from the central side I added
but I got error...
For nRF52832 I see in the datasheet:
I OFF_RAMOFF_GPIO System OFF, No RAM retention, Wake on GPIO,
While for nRF52840 only “System OFF, no RAM retention, wake on reset...
