Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hi,
I'm using Segger Embedded Studio with Ubuntu, trying to write a minimal code to let the chip start advertising.
I tried to read and understand the example codes provided...
Hi team,
customer used SDK v15 and the default s140 softdevice in it.
When the 52840 is configured in the 2M phy mode after connecting with Iphone 8/x, it can't be successfully...
Dear Sir,
Currently the example code in "ble_app_hrs" is written such that it advertise in connectable mode.
How can I modify the code so that it advertise in NON_CONNECTABLE...
Dear Sir,
I am talking with respect to the ble_app_hrs example in the SDK 15 for nrf52832. I am using softdevice S132.
In the example the code is implemented such that...
For instance, if I wanted to download the firmware that comes on the nRF52840-dongle in order to then write it to a custom board with an nRF52840 chip on it (i.e. so that...
Good morning,
I can't import the nrf_serial library ( and nrf_queue ) on the ble_app_uart project, after that i compile, i read these errors :
linking... .\_build\nrf52840_xxaa...
Hi,
I'm using 2 nRF52832s in my project. One of them is connected to a PC serially and has NUS central running on it and the other nRF52 connects to this central. I was...
I have two 52840DK, which can be used before, but I took it out and used it today. The led light on the rear panel of the USB is not lit, and the computer can't detect the...
Dear Sir,
I was trying to implement the following scenario.
Multiple phones initiate the connect request to a single peripheral.
On peripheral search for the phone...
I would like to confirm that my hardware design is correct and in addition that I am following the correct procedure to place the nRF52832 to sleep to achieve the lowest possible...
It works with SDK v12.3 and soft device 3.0.0. Does not after porting to 15.2. This is a custom board (extremely common configuration with single 32Mhz crystal) that serves...
Hello,
(I also create an issue over Thingy SDK GitHub page - #29)
It seems to me that there is an issue about the usage of MPU-9250.
I motioned Thingy and I observed...
Hi,
I am trying to get DFU working on my PCA10040 board using SDK 14.2 and armgcc toolchain.
I have followed the instructions to set up DFU here:
devzone.nordicsemi...
Hi,
Whenever I call `nrf_malloc` with a parameter bigger than 32, the pointer remains NULL. I think it's related to some sdk setting but I couldn't find it.
Anyone had...
Currently, I am working with the Nordic SimpleOnOff Model of the Light switch in the Bluetooth Mesh.
I am good that the light in the mesh can be set on/off after Provisioned...
