I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi, I am importing a bootloader project that uses softdevice s110 and NRF51822 from Keil to Segger Embedded Studio. I have got all kind of errors during the process and I...
Hi Team,
In BLE5,
1) Can we connect a peripheral device to multiple central device?
2) Is it possible to check if connecton fails with any central device in perpheral...
I'm trying to put thingy_sdk_v2.1.0 and 10 nrf52832 boards. I'm compiling "ble_app_thingee_s132_pca20020.emProject". I don't know why it's always an error. How do I demonstrate...
Hi,
I'm using nRF52832 and SDK 15 and IDE im using is Segger studio.
i have ported the uart code into Ble_app_multilink_central.When i debug the code it is getting stuck...
Looking for an example on how to advertise for 10 seconds then go into sd_power_system_off. Trying this by using ble_app_template (s112, ses, sdk15.0, custom, 1 led, 1 rgb...
Hi nordic
I bought the nrf52840 board so I'm developing.
I want to use the this kind of LIR2032 coin cell 3.6v ( www.amazon.com/.../B074VX8ZJF )
I measured power of...
Hello, I'm experiencing frequent endless loops at 0x16cbc with s132_nrf52_3.0.0 softdevice and SDK 12.3 on a custom board with Aconno NRF52832 module. I'm using SAADC and...
Please can you help me with this fairly straight-forward technical query for a customer new to BLE.
Please can you advise which is the best way to structure the link in...
Hello,
I am currently working on the development related to RSSI of beacon using nRF51_SDK_9.0.0_2e23562(SDK). The beacons I’m using are developed with this SDK as well...
Hi guys!
I want to select NRF52840 as my target platform. Is it possible to start software developing on 52832 (for which I have devkit) and then seamlessly move my code...
Hello, I want to do a project with Segger Embeded Studio using the nRF52840 with the SDK_Mesh I have 2 nRF52840 cards and I want to transmit data to a mobile phone using a...
i compiled the ble_uart_app project it got downloaded in to the NRF51DK but the bluetooth is not getting turned on ,usually the output of this example is LED has to be turned...
Thanks for your support folks!
I am trying to read some bytes I have wrote in a MX25R8035F. From the datasheet, if you send 0x03 (READ) + 3 Byte address, then the memory...
Hi,
We want to receive the data in laptop over the BLE like nRF UART mobile APP.
we sending and receiving data in Mobile app but we can't get the app for desktop.
we...
Hi,
1-I did some test for nrf51422 (SDK12.3 + soft device S130) power consumption. result as below:
-system on sleep mode( without UART and BLE Advertise ):90uA
-system...
