I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am developing a program with BMI160 with this libraries , but I do not know to which it refers the following code at line 5 and 6: sensor.read and sensor.write.
It is...
I’m using the example “light switch” of SDK Mesh.1.0.1. In my case, i use nrf51 dk as client and three nrf51 dongles as servers but It doesn’t work.
I have tried to debug...
Hi everyone! I'm trying to generate a modulated continuous signal in a specific channel using nrf52832. I used a code made from radio_test example that follows. The problem...
when i program the code firstly , the device is not broadcast,But the other is running well. the output log is correctly.
when i reset the device several times , the device...
Hi, I have done some developing for nRF51822 with Keil before and now I have started out with a new project using Segger so of course I wanted to use the lastest SDK with...
While writing a hardware (I2S) assisted software UART I have noticed that the SDK 14.2 seems to be missing two enums for 32MDIV30 and 32MDIV32
Below is a diff from my private...
Currently I am scanning with a window of ~23ms and an interval of ~33ms. I am also advertising with an advertising interval of ~330ms. Using radio events, I notice that the...
Hi,
I am seeing a couple of issues in my Android mobile app while doing a DFU:
1. The DFU stops in the middle with this log on the debugger
I/art: Starting a blocking...
now i use nRF52832 and my using paccage is SDK14.0.0
i could send data from phone to nRF52832.
next i wanna send data from nRF52832 to phone.
but i don't know where to...
nrf52832
SDK 14.2
NVMC and SD backend both
Hi,
I had a question about the nrf_fstorage_read function. In a previous answer , it was mentioned that fstorage_read function...
Hello,
on GitHub I foudn an out of the box example for bluetooth mesh with multiple Thingy-boards ( https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo ). The...
Dear Nordic Team,
Thanks for supporting.
If any possible to add manufacturer data in example experimental_ble_app_blinky in advertisement. i am using SDk11 and my hardware...
Hello,
I have been trying to read the temp , hum and pressure value using BME280. The problem i face is i get the same value constantly and it doesn´t change.
I am trying...
My SDK version is NRF51_9.00, softdeive 130, board nrf51822.
We want to confirm some questions about BLE muti connection
1. When NRF51 is scanning, could it connect with...
Hello everyone,
This is the second time that I've had the problem I am about to describe. I fixed it, and now it is broken again. I am fairly certain that it is not (only...
