hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hi Everyone, I'm trying to know and make a handler for the ble advertasing, and I've front with the doubt if there's a way to know when the program will change of advertising...
We have designed an electronics product - a PC peripheral and are looking to release it to market. It’s basically a ATSAMD21 microprocessor connected to a battery, which charges...
My requirement is to send 16kHz 1channel voice data stream to pc .
I use 16khz (2 channel and 1 channel) wav and 1 48khz (2 channel) wav as input (converted to .c file)...
Hi Nordic team,
I was working on nRF DFU (secure_bootloader_ble_s140_pca10056) .I just want to advertise my device mac id to Phones app while in OTA mode to specify devices...
We want to use the iperf3 tool to measure packet loss while sending packets between two nRF52840 DKs. But we can't seem to find any instructions. We are using a variant of...
Hello,
I use zb_cli_wrapper.py and the Zigbee Cli Agent Router example.
I try to discover attributes from a GreenPower endpoint (242), the commande is :
communicator...
Hi,all~
The program runs on nRF52833.The SDK version is NRF5_SDK_17.0.2_D674DDE. At the beginning, MCU sends data to nRF52833 through serial port, and the data can be received...
Hello,
It looks like a possible policy issue - but I was wondering if anyone here has successfully provisioned IoT in this Amazon AWS Region/Endpoint: iot.ap-northeast-1...
I am trying to deploy an trained Impulse module into nRF52840, but not sure about how to do it.
In the edge impulse documentation, they mention we can link the impulse from...
We've been chasing a seemingly randomly appearing bug, where a call to the Zephyr MQTT library seems to sometimes block indefinitely. More specifically the hanging function...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
When receiving advertisements, "nrf_ble_scan_filter_set" is used to filter the device...
Hi ,
There is an error when to debug the nRF52840 target board by the PCA10028 board(as error information).
(pls note, There is running okay when to debug the nRF52840...
I have an nRF52805-based BC805M module from Fanstel. I need to control it from an MCU over serial/I2C/SPI to implement Bluetooth profiles like BIP and FTP. I prefer canned...
