hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hi:
When nrf52 series chips use 32.768KHz crystal oscillator as RTC clock source, the operation error is large at low temperature. Therefore, the following problems need...
I am working with nRF52811 and having a problem with programming and reading flash memory.
I am using J-Link programmer connected with USB.
In nRF Connect Programmer the...
Hello,
I am trying to run the demo thread DFU example by following the docs but without any success. I somehow managed to reach the last step where I have to set DFU server...
Dear Nordic,
could you please suggest what should be done to make USB console & shell options work? What should be checked?
It was quite fine on nCS v1.5.1, and completely...
hi support team，
customer want to setup a timer with 800 us and then 1200 us and then repeatedly without any delay.
for now i use timer to set channel 1 with 800 us cc...
Hi all,
I am using NRF5340 in my custom board. The spims are working well, they are developed by nrfx lib in NRF SDK 1.5.1.
However, after I updated my sdk to 1.6.1, the...
Hello,
I was looking over the board -nRF52 DK- and saw a solder bridge labeled as SB31. But I could not find an information about it in the documentation . Could you please...
Hi All,
I have developed a Bluetooth application with nrf52840, which can be upgraded through our own APP (implementation 'no.nordicemi. Android: DFU: 1.10.3'). However...
Hi All,
I need to do RSA encryption and decryption using nRF52832. I am planning to use mbed TLS library.
Can you please help me to share some example code which can I...
I have encountered some problems when trying to use ENC28j60 ethernet module with nrf52840dongle and hope to get some help from here. Problems:
No internet access on Ipv4...
Hi
I try to run a nRF9160 on a nRF9160DK with lowest power possible.
A wake up from pin and periodically from RTC is required.
In the nRF9160_PS_v2.0.pdf is IMCUON1...
Hello,
We have a Xamarin Forms application, which we use for connecting to nrf52840 device and read/write characteristics. We managed to do it using Plugin.BLE nuget available...
I have difficulties in decoding the nRF9160 GPS output data. I know that nRF9160 reports its GPS data in NMEA GPGGA format, however, I am wondering why the last number which...
I want a waveform as below for motor control. I am trying to create this using nrf pwm driver.
I set the pwm sequence as below and checked the output. 2nd duty repeat does...
