hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello support
I have modified the cli examples and run into "undefined reference to `nrf_cli_uart_transport_api'" linker error.
The error message is
Compiling file:...
Here's my setup:
1. RPI4+nRF52840 dongle as OT border router
2. nRF5340DK running CoAP client example application
3. Wireshark running on Mac OS, with nRF52840 dongle...
Hello!
I'm trying to develop a mesh network and I've been building on top of sensor example, which has been very useful since I'm reading a few sensors. However I want to...
I am trying to generate ECC key pairs using MbedTLS on Connect SDK.
I found this code block on stackoverflow and validated from mbedtls/programs.
"mbedtls_ctr_drbg_seed...
I was trying to evluate the Periperhral ISO server, however with a NR52dk, but it returns ENOTSUP.
Bluetooth initialized Unable to register ISO server (err -134) [00...
Hi all
I am developing a proprietary radio protocol application using the nRF52805. I am not using a softdevice. Instead, this is all done by accessing the radio registers...
I have seen this question answered for the old Nordic SDK but have not been able to find a solution in Zephyr & NCS. I'm following this post on how to develop a custom BLE...
Hello,
i am using nrf52832 dev kit want to send the nrf calendar parameter through nrf connect app and send through app successfully by taking uint8_t datatype .I have receive...
Hello.
I am trying to write code to read data using saadc and write the sampled data in a micro SD card using fatfs.
I started from the fatfs example and initialized...
I'm attempting to use pc-ble-driver-py on Windows with an NRF52 DK (PCA10040) and running into the error shown below. Using the Heart Rate Collector example, the COM port...
Hi,
I'm using the ble nus uart for my application and I noticed that I was drawing too much current so I went back to the example from the SDK 17.0.2_d674dde which I haven...
I have followed the Azure IoT Hub — nRF Connect SDK 1.6.99 documentation (nordicsemi.com) and was able to comminicate with Azure IoT hub.I have created rootCA and device certificates...
This is my problem description, hope someone can help me. 1. The watch product shipped in mass production is found to be disconnected when using the mobile phone OPPO-k7x...
HI,
i have enabled CONFIG_BT_SETTINGS_CCC_STORE_ON_WRITE=y
so after power cycle the device automatically connects with iphone and the service also works fine
after this...
