I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
I'm using SDK mesh v1.0.1 and nrf51822 S130 for mesh application. Light switch example is working fine. Now I want to add a twi sensor in server side. My doubt is in mesh...
Hello,
First, the current of the advertising frame was too high (around factor 2) and I have switched on the DC-DC to correct for that by inserting sd_power_dcdc_mode_set...
Where could i get the apk of thingy 52? it's hard for me to log on the Google play to install it because my phone didn't have GoogleServicesFramework, could anybody send me...
I am working on RTLS project. In beacon i am advertising battery life and temperature along with minor number and RSSI . I am merging battery strength and temperature in major...
Hi!
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
* android ver.8 smartphone with nRF Connect
I have implemented the...
Hello I'm using a macbookPro 2016 which only has usb-c and I can only connect the dk through a usb hub.
I have already installed the nrf5x-Command Line Tools for OSX but...
Hello everyone, i'm currently doing a project with nrf52832 and i just came across a problem. I configured 3 pins as output, then i set 2 pins to high and 1 pin to low. But...
I would like to implement UARTE.
· Nrf 52 · SDK15 · S 132
The big advantage of EasyDMA is that it does not issue interrupts for each byte received. In nrf 51, "app_uart_get...
Dear Sir/Madam,
Normally battery level notification is only one byte. But I need send byte array of 58 bytes through battery level notifications in my project. I have to...
I am developing my code in a custom nrf52832 breakout board. My code was modified from the example "ble_app_uart".
I find a high current issue with UART. The current is...
Hello,
I am trying to evaluate the NRF52832 on a custom board and i will design the antenna according to your NRF52 Thingy:52 design. I am quite a newbie about RF&Antennas...
Hello
I'm using SDK 15, S132 PCA10040
I have followed this tut.
I've tried 2 scenarios which in both I get error value:
1. when advertising_init() is before services_init...
Hello,
I saw this , but I was struggling with the merge for quite a long time now. Is there any ready example for e.g. provisionee or provisioner from light_switch merged...
Hi, Nordic!
I wanna know how change characteristic(service,Rx,Tx) UUIDs .
For example,
Proximity UUID : 01020304 -0506-0708-0910-111213141516
Service UUID : 01020304...
