Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I've just got my hands on this amazing little thing call Thingy 52. I have played around with the default app but now I'm struggling with flashing a custom firmware...
Hello,
I am trying to setup two Thingys with my node-red system and i have ran into some problems. The thingys respond to normal command line tools like gatttool, btmgmt...
Hi All,
I am new to Nordic microcontrollers. I am using keil uvision MDK lite version. After I have uploaded a source code and when i am trying to compile. I am getting...
Hello,
I am starting a new thread concerning the two messages that I have posted about generating a 4MHz clock on nRF52832. I am using the nRF5_SDK_14.2.0_17b948a SDK. ...
Hi,
if I correct understood DFU process first of all it need to send "Init packet" and after that it need to send FW image. And for that reason in DFU packages is 3 files...
Sir, i am looking to design customized board using nrf52832, i have pca10040 borad as well. i am looking for eagle library of antenna used in pca10040 (i.e nrR52DK).
if...
Hi, I'm trying to program a nRF52-DK, with a workong firmware, and a board that was working, but I can't manage to flash the DK.
With a make flash_softdevice:
Flashing...
I am working on nrf52832 BLE. I have used soft device s132. Antenna device is as per the reference design of NRF52832 and have used 32MHZ crystal for HFXO oscillator. but...
I am starting analysis for project of BLE Central device that is only receive broadcasting packet (advertise) from peripherals.
However, it’s unclear to me. I doubt will...
I notice that the sensitivity for the nRF52832 is defined as being ~2dB better in BLE mode than in NRF mode. I have also tested this to be correct.
However, I wonder - is...
Hi!
We have several products which use SoftDevice S110, some of them are already in production and are listed as Bluetooth Qualified, some of them we are preparing for production...
I've a custom board that uses a nrf52832 and Li-SOCl2 battery (3.7V). We've programmed several boards with our firmware and kept then with BLE advertisings every 300ms. A...
I am trying to develop a simple SPI master for a custom nRF52832 uC, but I can't find anny sort of sample codes that don't use Soft devices for this task. I need the code...
hi guys. I am currently using nrf52832 MDBT42Q Series from Raytac. I would like to know that how can I flash the softdevice and my application into the nrf52. My NRFgo unable...
