I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hi,
nrf51822 device obverse six bytes mac addres could change，when OTA failed.
six bytes mac address, five bytes fixed, one byte can change when OTA failed.
Now，my app...
Hello,
I am using Nordic Nur-10W develop kit, trying to compile NurApiExample in Raspberry Pi. I wrote a Makefile, and complie process was OK. However, undefined reference...
hi
im using sdk v6 and when i turn my board on it goes to bootloader and i can upload my program into it .
the problem is that i want it to run to my main program after...
Hello,
I would like to use a custom flash memory layout for the flash memory of nrf52:
I thought that I should be able to use the UICR.NRFFW[0] - if I set to the start...
Hi, I use PCA10040 v1.1 with SDK12.1 via S132 v3.
I use Keil 5.21.
After testing the LBS example, I was merging the NUS (NORDIC UART Service) to the standalone LBS example...
I am working with nrf51822 board softdevice of s130,sdk11.0 version.I want to create 4 KB of Flash through PStorage.I am able to create 1 kb(maximum block size ) of flash...
Hello everyone,
I'm doing some work in SDK 12.1 and noticed that even the example peripheral project "ble_app_template" compiles to 26K under Keil. Given there is a 32K...
Iam using SDK10.0 and Softdevice version S110, i use device manager to monitor connections, i have implemented passkey pairing. nRF board is peripheral and iam connecting...
I have a project using printf to send AT commands to a cellular modem. It works well.
Yesterday I added Segger_RTT into the project.
With NRF_LOG_USES_RTT=0 defined.
...
I'm trying to get an a recognized ble pulse without using a softdevice. I started with the basic transmitter application and am trying to decipher the order for the data I...
Hello,
I am trying to get my device (nrf52832) to do DFU OTA, and to do so I am programming the bootloader before programming the s132 softdevice and the application. However...
Dear Colleagues,
I am much obliged for your kind assistance to me.
My Question:
I have setup my NRF8001 successfully (please find the setup file generate by the nrfgo...
Hi,
I use SPI Master driver to communicate with a flash memory.
I use SDK 12 and i use nrf_drv_spi_transfer(...); to write and read over SPI.
My problem is the following...
We are using SDK 11 and SD v2. I did a search for an answer to this question, but couldn't find one that addressed it fully but what I gleaned is that this may not be possible...
