I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hello,
Because i want to connect more than two headset to one gateway, so i modify the prj.conf as follow
CONFIG_AUDIO_DEV =2
CONFIG_BT_MAX_CONN =4
CONFIG_BT_MAX_PAIRED...
Hey all,
Quick question. If we want to send BLE advertisements, beacons, for just 1-2 seconds, then shutdown into SYSTEM_OFF mode, could we initialize the BLE soft device...
I using XIAO nrf52840. https://wiki.seeedstudio.com/XIAO_BLE/
I am developing a BLE peripheral device using the nRF52840. This device is designed to connect with a specific...
Hi,
Could you please advise, am designing a device using the nrf52dk-52832 in nrf sdk connect 2.5.1 and toolchain 2.5.2 that reads the previously adquired samples data from...
Hello,
We decided to use the 802540 battery for our application with the nPM1300. To get a good estimate of the state of charge (SOC), we did the very lengthy battery profiling...
Greetings
I am looking for a conceptual guide to adding my own services to the BLE stack, with Zephyr. Is there any documentation or guide for this? I am working on the...
Hello, I am having an issue with DSP library basicmath where the source file does not seem to be included in the build and I am getting error undefined reference to `zdsp_mult_f32...
Hi,
I am using nrf5340 with v2.5.1 toolchain
I have an out-of-tree driver, where i want to include adc_context.h from and have added:
target_include_directories...
Hi I'm trying estimate the nRF52840s current with the Online Power profiler, the data seemed a bit unclear to me.
I have used the following setting: Chip nFR53840 Voltage...
Hello,
I am trying to do CE, FCC RF test.
I am using nRF52833 and nRF5_SDK_17.0.2_d674dde.
I want DTM to work. DTM is using example source in SDK. What changed in...
I am trying to develop a Consumer Control device. I found the "nrf51_ble_app_hids_kbd_consumercontrol-SDK15" example code on Devzone. But this example code can only do 8 Consumer...
Hi, I have been using nrf52840(my application) and nrf9160(Serial LTE Modem : SLM , which modem firmware was ver1.3.6 and application firmware from switch science )
First...
I tested the matter LOCK sample, how to disconnect the Bluetooth connection immediately after matter commissioning is completed, the log is as follows. thanks.
Hi, I am currently evaluating a Rust driver for the nrf7002-ek on a nrf5340-dk. I have been using the Zephyr nrfwifi driver for reference.
There are a large number of nrf_wifi_fmac...
When building a project using a custom board, as well as both the b0 and mcuboot bootloaders enabled, board-specific child image configuration causes the build system to ignore...
