Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
I'm restarting development using an older nRF Thingy:91 .
When I first started up "nRF Connect for Desktop" and the "Cellular Monitor" a few weeks ago, I managed to get...
Hi,
starting from ncs 3.2.0 (also in 3.2.1) when i attached the debugger (jlink ultra+, under VS code with nrf connect extension) to my nrf52833 board, i am getting the...
Hello,
We're working implementing a custom board using he nRF54L15 and looking to use the NFC functionality. We have run into an issue that occurs when we try to read the...
Hi, I'm trying to determine whether or not an nRF54L15-DK running Zephyr supports the following relatively recent Bluetooth features and if so, how to enable and use them...
Hi, I'm using v4.0.4 of the standalone Bluetooth Low Energy desktop application to obtain and display GATT details of a connected device. I enable indications on the Service...
One of our employees is following the Cellular Fundamentals courses and they got stuck on getting modem traces out of the Thingy:91X.
In lesson 7 exercise 1, the course...
I have been trying to understand Child Supervision. Part of the documentation that I have read is:
https://openthread.io/guides/build/features/child-supervision
At the...
Hello!
I'm working on a project that was primarily developed with NCS v2.9.0. The application (using an nRF5340) utilizes BLE mesh and is configured to use TinyCrypt for...
Hello,
I am using nRF52833 with nrf connect sdk for vs code (SDK and Toolchain version : 2.9.1).
Hello Nordic Team,
I am using OTA DFU with MCUboot on the nRF Connect...
I have a custom NRF9151 board with Windbond W25Q32JV flash, and some other peripherals connected. It also has GPS and LTE which I have tested and work. My UART console is...
I am trying to flash and use the debugger on a nrf52840 DK to flash a Thingy53, using the ribbon connector as outlined in this video . I tried to follow the steps in this...
nRF9160, SICA B1A, mfw 1.3.7, NCS 3.1.0
I currently try to test the situation, when the battery gets drained "too much" and the voltage drops below 3.0V (e.g. 2.9V) on VDD1...
Hi Nordic Team,
I am using MCUBoot with BLE DFU on nRF5340 and I am facing an issue where the DFU process cannot complete due to my application’s custom boot logic.
After...
My project is running on an nRF52832 with the soft device enabled. At the start of my project I have the following
When I reset the system our normal way (calling nrf_pwr_mgmt_shutdown...
