I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
Hi,
I've got a custom board with nrf52832 mcu. I use the nRF5_SDK_16.0.0_98a08e2 with s132_nrf52_7.0.1_softdevice.hex.
Sometimes the app_error_fault_handler is called...
Hi,
I have a project based on the NUS (Nordic Uart Service) example.
I have bought a USB dongle MDBT50Q-RX manufactured by RAYTAC ( https://www.raytac.com/product/ins...
When I tried to send data in the form of float it shows an error and I changed it to another format as sending flag, mantissa(3 bytes), and exponent (1 Byte). Can anyone help...
To the kind attention of Nordic support team,
I have got an nRF52840 working application using usb and gazell, and I'm porting it from nRF52840 to nRF52833 these days. Yes...
I have some nRF52832 devices that have been flashed with a Softdevice v13 based firmware and can receive OTA firmware updates. Unfortunately their enclosures are sealed and...
Hi,
I am attempting to get the adxl362 sample working with the nrf9160 dk board. I am using the nordic SDK v1.2.0. I cannot get it to compile, compiling the code below fails...
Hello,
I am using SDK SDK_15.3.0_59ac345 in application that receives data from UART, and the aplication is running in background just ADV.
In the main function, after...
Sir,
With reference to the subject cited above the undersign is working as Assistant Professor in CSE Department and doing R & D in IOT.
I want to recommend your product...
Hi There,
ISSUE:
New Nordic Thingy:91 will not connect to the LTE network, it is giving:
2020-03-25T18:10:10.221Z DEBUG modem << cloud_connect failed: 22 \x0D\x0A...
Hi,
I'm working around to integrate FreeRTOS to Libuarte example, but i'm getting an error while building the project says:
For the Libuarte instance i'm using RTC instance...
Dear Sir,
I want to do the following scenario.
Once I power the device it will start advertising.
Now the advertising duration is 2minutes.
I have written...
I have a nRF52832 dev board and a separate J-link programmer. I want to do a sanity check on the programmer and I was wandering if there is a way to program the dev board...
I'm studying to perform DFU Peripheral from Central both using nRF52840, I'm able to issue command to let Peripheral into DFU mode, but got a "Received a fault" message in...
Hello,
I am using nRF52832 chip for freeRTOS project and using RTC2. I have SDK15.2. I want to have timestamp from RTC as hex format. I searched almost all forums but i...