Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi, I took a look at the low power comparator example from the Nordic SDK and test it with my nRF52-DK and I found out that the comparator isn´t triggering when I set the...
Hello, I have a problem with the I2C peripheral on my nrf53840. I enable i2c driver on my project and read sensors on the bus. Everything is OK. Then when with Power management...
Hi Nordic,
I am working with the s140, sdk 15.3. My application is a central that should connect to a device that has several services. As soon as the connected event is...
Hello,
I am using nRF Connect for Desktop 3.7.1 with a nRF52840 USB dongle for testing purposes.
In the Bluetooth Low Energy 2.5.3 application I deselected the "Auto accept...
Hi,
I'm using Nrf52840 to connect to a Mobile via BLE.
I'm advertising to start connection, and after bonding, I can start advertising with whitelist in order to connect...
When adding this line to codes from an article here control reaches
Example used is ble_app_hrs_pca10056_s140 on nrfDK2 , sdk 17
==================added to advertising_init...
Hi,
I'm trying to use Thingy91 as a gateway for collecting data through BLE (from other thingy52s) and send it to Azure IoT Hub using LTE, but the current sample code only...
Archlinux
Visual Studio Code: Version: 1.58.0-insider
nRF Connect: v2021.9.98
I installed the "nRF Connect" extension in vscode, and went to look into a problem I was...
Hi,
I'm currently testing LPCOMP with one of our nRF5340DK boards.
The power consumption of the LPCOMP seems way too big (around 140µA) once enabled with this conf...
Dear Nordic Engineer
Our customer uses NRF52832 to develop a computer remote control pen. They are based on the keyboard example in the 15.3.0 SDK. Now they encounter some...
I have a working (hand-wired) prototype that connects to the internet without any problem.
Now I have made a PCB to replicate the same thing and loaded the same software...
Hi, I do have a PCA10040 board, I'm using the examples from Nordic. On the DFU example for SDK 12 I have pressed button 4 and RESET the board to active BOOT . I’m testing...
Hi,
S112/S113 is currently the only supported SoftDevice on nRF52805 and doesn't support Central (Only Peripheral). Is there a plan to enable S132, SoftDevice Central are...
Hi,
I have nRF52840 DK boards.
This is rather an informational question for my benefits.
In post: https://devzone.nordicsemi.com/f/nordic-q-a/9315/nrf52-802-15-4
...
Hi,
I’m developing a BLE joystick with nrf52832 with a PCA10040 board
To make the development simple I’m using 16 input Buttons and 2 analog inputs with 8 bits each. ...
