According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi:
When nrf52 series chips use 32.768KHz crystal oscillator as RTC clock source, the operation error is large at low temperature. Therefore, the following problems need...
I am working with nRF52811 and having a problem with programming and reading flash memory.
I am using J-Link programmer connected with USB.
In nRF Connect Programmer the...
Hello,
I am trying to run the demo thread DFU example by following the docs but without any success. I somehow managed to reach the last step where I have to set DFU server...
Dear Nordic,
could you please suggest what should be done to make USB console & shell options work? What should be checked?
It was quite fine on nCS v1.5.1, and completely...
hi support team，
customer want to setup a timer with 800 us and then 1200 us and then repeatedly without any delay.
for now i use timer to set channel 1 with 800 us cc...
Hi all,
I am using NRF5340 in my custom board. The spims are working well, they are developed by nrfx lib in NRF SDK 1.5.1.
However, after I updated my sdk to 1.6.1, the...
Hello,
I was looking over the board -nRF52 DK- and saw a solder bridge labeled as SB31. But I could not find an information about it in the documentation . Could you please...
Hi All,
I have developed a Bluetooth application with nrf52840, which can be upgraded through our own APP (implementation 'no.nordicemi. Android: DFU: 1.10.3'). However...
Hi All,
I need to do RSA encryption and decryption using nRF52832. I am planning to use mbed TLS library.
Can you please help me to share some example code which can I...
I have encountered some problems when trying to use ENC28j60 ethernet module with nrf52840dongle and hope to get some help from here. Problems:
No internet access on Ipv4...
Hi
I try to run a nRF9160 on a nRF9160DK with lowest power possible.
A wake up from pin and periodically from RTC is required.
In the nRF9160_PS_v2.0.pdf is IMCUON1...
Hello,
We have a Xamarin Forms application, which we use for connecting to nrf52840 device and read/write characteristics. We managed to do it using Plugin.BLE nuget available...
I have difficulties in decoding the nRF9160 GPS output data. I know that nRF9160 reports its GPS data in NMEA GPGGA format, however, I am wondering why the last number which...
I want a waveform as below for motor control. I am trying to create this using nrf pwm driver.
I set the pwm sequence as below and checked the output. 2nd duty repeat does...
