Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
In my previous ticket regarding DevAcademy tutorial for nRF 52840 I already mentioned. that starting from lesson 2 iPhone cannot communicate with the board and the VS Code...
Are there any current or future plans to implement Curve25519 (also known as Ed25519) for the NSIB?
It appears that the CryptoCell 310 supports it, and it is recommended...
MCUboot supports software security count based download protection. But it is found that it is not exposed by nRF SDK. It adds the "--security-counter" argument only if
...
Hi All. I am a beginner trying to complete the DevAcademy SDK fundamentals level course, and since I seamlessly completed lesson 1 on the Blinky sample, I reckon my toolchain...
NCS 2.5.2
Toolchain 2.5.1
NRF52840
Hi,
I'm currently power profiling our custom board. So far I've managed to get the current consumption quite low (6.5uA at 3V...
I am in a need to measure a battery level under a constant load. Rather than adding a custom electronics, I am considering using the radio. I believe there is a way of doing...
Hello,
I am attempting to use a J-Link or a FORTE programmer to interface with the debug port to upload a new binary/program to my board. Is this possible? I am trying to...
nRF52840
NCS 2.4.1 to NCS 2.6.1
My project is based on the coap_server example. When I ported it from NCS 2.4.1 to NCS 2.6.1, the network key and PSKC changed. All other...
SDK: v2.6.0. nRF5340 custom board
Hello I'm trying to do an static partitioning scheme using a pm_static.yml file and also I want to use NVS to store some data.
The...
Hi!
First off: I know the Cryptocell register interface is not officially supported, but I'm using it for learning purposes and I'd like to understand what's happening....
Hi, Using ncs v2.7 on the nrf9160, is there a data limit using MQTT to communicate with Azure IoT Hub per message? I'm trying to determine if I will need to chunk my telemetry...
We are developing a sleepy end device using the nRF52840, using light switch sample . The end device is connected to a Zigbee coordinator, also based on the nRF52840.When...
We are using a 5340 with a Skyworks 66112 FEM. Below is our hci_ipc.overlay file.
We are setting CONFIG_BT_CTLR_TX_PWR_ANTENNA =20. When we measure the output of the FEM...
