Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi,
Is it possible to join an existing mesh network with a provisioner made on Nrf52840 (s140) ?
I have used the provisioner example to make a provisioner which actually...
Hi everyone,
I am working on a project, currently developing on the nrf9160-dk board. And I want to enable AWS and AGPS together in my project. And once I've enabled them...
Hi.
I modified the fstorage example to create the project.
I split Flash into three areas as shown below.
*Flash Area(0x26000 ~ 0x2ffff) : Bootloader
*Flash Area(0x30000...
Hello Nordic team,
We are making our own custom project, and we are facing problems in implementing lower power modes.
Reading from the info center, when the DK Board...
When initializing two channels, enter scan mode。After the two channels are converted, the callback function will be entered，Read conversion results。However, the requirements...
Hello
I am following a beginners tutorial on youtube and trying to implement simplest possible example of reading an analog value.
I want to use the nrfx library to do...
Hello,
I am working on a project where I am using 8 ADC channels on the nRF52832. When I run the code the device seems to get ADC values that look correct. But, if I pause...
I have an out-of-tree driver. It has an I2C that is working but also GPIO that are only working with compatible = "gpio-leds" but not with the driver compatible = "st,vl53lx...
On the nRF52840 there were many pins specified as "low frequency I/O only." Does the nRF53 have this same restriction? I don't see mention of these pins in the nRF53 datasheet...
Hello, I am working on application with nRF52833. What is max load current of internal LDO between VDDH - VDD? VDDH is 5V (USB) and VDD is 3.3V. There isn't anything about...
Hi
I am not busy developing an new product with nRF52840.
I want to use the BLE functionality and started with the ble_app_hrs sample application.
I download the pca10056...
Hi everybody,
I am trying install and set up Wireshark, i am in this step:
this is my output:
I think trhe problem is because of pyserial isn't detected, i have...
Hi,
I purchased a BLE dongle with your 3rd party HolyIoT: mini Holyiot-nRF52840-USB-Dongle. It is recognised on Nordic Connect, but not Nordic Programmer (Err msg: DFU trigger...
Dear devzone-team,
could you please tell me where the yaml files (like thingy91_nrf9160_ns.yaml) in the board folders are used?
I could not find a tool which evaluates...
