The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi, Aim :- To Configure SAADC Sampling Rate at 200Khz. SAADC Configuration :- 1. The resolution, oversample, interrupt priority and low power mode are set as 12 bit, OFF,...
Hi,
I am planning to design a device based on nRF51-dk but with external programmer. I have ST-Link available so I thought I just provide a simple walk through showing...
Hi, all
I tested nRF5_SDK_17.0 ecdh example (path: \examples\crypto\nrf_crypto\ecdh), config with MBEDTLS, CC310, uECC separately and add a gpio toggle to measure timing...
Is there any problem if I stall older version of nrfjprog in my apple Macbook? Will there be any conflict with the new version already installed. The new nrfjprog have the...
Hi,
I'm trying to send and receive scan request/scan response. The system consists of 2 nrf52840, 1 central and 1 peripheral. They both advertise and scan on 1M and coded...
I'm currently working on a program that automates the Legacy DFU procedure and I'm running into some strange issues with writing to the DFU characteristics.
On the nRF Connect...
Hello,
I am trying to use the FDS module with the Softdevices and Peer manager.
I can store some data and I am able to read the header of the record, but when I try to...
Hi,
I want to use the static version of pc-ble-driver in my c++ code. I am learning cmake but I have no expereince with Ninja. I'm using only the version 6 of the API. My...
Target application 1: Data acquisition is carried out for a 0-1khz high-low level signal. The low level is effective. The count is increased by 1 for each trigger. 2: Use...
Excuse me:
I'm developing a keyboard with nrf52832，Calling ble_hids_inp_rep_send() returns BLE_ERROR_GATTS_SYS_ATTR_MISSING when the keyboard is just connected to ipad4...
Hello All,
I am developing a prototype for one of my application.
I am trying to integrate the zigbee stack to my base firmware.
For my application I am using RTC2....
Hi,
I'm using the example "ble_central/ble_app_uart_c" of nRF5_SDK_17.0.2. Connection to peripheral workes fine.
If the central re-starts while a connection is established...
Hello, there
We made a custom tracker device with nRF9160. During prolonged use, we observed that k_delayed_work_submit_to_queue sometime return -22 and cannot be recovered...
