The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Please allow me to introduce myself, I am product Engineer at Epson Electronics. I am supporting Nordic on Reference Designs.
I noticed in the new nRF5340 there are two...
Hi Nordic:
I think this should be a same old question, but as following thread mention:
https://devzone.nordicsemi.com/f/nordic-q-a/38292/mesh-proxy-sdk2-1-1-tx-power...
I am attempting to provision the sensor mesh example using the static provisioner example from the MESH SDK.
It works great. However, the client receives two broadcasts...
Hi community,
Starting with a new product on the nRF52, I was playing with the Serial Flash of the nRF52840 DK.
I have been using similar Serial Flash on other platforms...
Hi !
I'm trying to debug. I followed this video : https://www.youtube.com/watch?v=uP8RYgYGRvI&list=PLx_tBuQ_KSqGHmzdEL2GWEOeix-S5rgTV&index=7 . But I can't completely. ...
I would like to use nRF52 DK (nRF52832) to program Fanstel BC805M EK (nRF52805) . When I upload to code from nrf52 DK to BC805M, I got this error message.
I know that...
I have many of these types of systems running in a single room but when I try to run more than 8 I start start to get errors. How many systems should be able to run in the...
I am creating a saadc project based on the ble_app_uart project.
The source code is as follows.
If you download after compiling, the following operation is performed...
Hi, all
I am studying the bsp part while looking at the example of 'ble_app_uart'. (pca10056)
The difference between 'bsp_event_handler' and 'bsp_button_event_handler...
Hi DevZone,
I want to perform USB bulk transmits to a host device while using the app_usbd library. I am using SDK 15.3 and the s140 soft device is enabled.
I have found...
Hello Nordic Team;
The Vdd value range for the nRF9160 is 3.00 V to 5.5 V. We will use li-PO battery in our system. Can I power the nRF9160 directly from the battery without...
Hi,
I am using Nordic thingy 52 for my application, Now I need to blink LED for 5 seconds on Board when ever a condition is satisfied. But in schematic of Nordic thingy...
Board: nRF51-DK (nRF51422 chip)
SDK: 12.3.0
SoftDevice: S130
Compilation settings
Optimization level O1
Debug information generated
I have seen lot of...
Hi.
I am going to make my own PCB with nrf52832.
Before making it, I have to check debugging through P20 in nrf52832 DK.
I have two nrf52832 DKs with SDK17.0.0....
