The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi,
We developped a custom NRF9160 board and it works fine, it connects to LTE-M. We then designed a new version of the same board by adding few things (like NRF52833 MCU...
The sample code at ncs/nrf/samples/nrf9160/mqtt_simple is not connecting. I dod not make any changes to the ode. I am using NB-IoT. LTE is connected. The link monitor, LTE...
I just spent hours trying to use TTM with nRF52840 and I wanted to share the fix:
You need to use the Thread FTD CLI (USB) pre-compiled binary from v4.0.0 of nRF SDK for...
I would like to clarify my understanding of the connection interval since it doesn't seem to match what I'm seeing in the nrf connect mobile app.
Currently I've set my...
Hello all!
I have been modifying the door_lock_nus example to add the set pin command (0x05 from zcl reference). So I have modified the zigbee callback to read the new...
Hi,
I am wondering how to let these both run together. If I understand the sdk_config correctly the app_scheduler event queue can be used for the USB directly. But how should...
When performing a DFU the 2nd stage increments the expected device BLE address by 1 when the device being updated reboots. This potentially conflicts with the address of an...
We have developed a PCB using nrf52840 controller. It's a brand new controller. I am using SEGGER embedded studio for programing.
I have flashed an example code ble_app_blinky_pca10056_s140...
If one using nRF52840 microcontroller as non-RF one, in example configuration from page 593 / Figure 214, No 6 schematic, I have two questions
- does a ANT pin filtering...
hello Nordic
i am working with nrf52840 dev board, sdk 16.0, based on the peripheral app_ble_blinky example.
i have 2 spi comms, one twi, and use rtc, app timer and...
Hi,
I'm using nrf52840 and connecting to a mobile device via BLE.
After bonding connection, I'm restarting my nrf device in order to start advertising again, with...
Hello All,
I am new to this field and would like to know technical details of this field. I want to develop a product using NRF52833-QIAA-R7 or NRF52840-QIAA-T
Anyone...
Are there any examples showing how to handle MQTT QOS 2? I have searched for MQTT_EVT_PUBREC, MQTT_EVT_PUBREL, and MQTT_EVT_PUBCOMP and nothing shows up for any.
