I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
Hi,
I am facing a frustrating problem in my project: I am using Nordic nRF51822 running on UART application SDK 11. The problem comes to when I add peer management and DFU...
Hi,
I am trying to build the connectivity firmware for a custom dongle based on the nrf52832. I am getting a section overlap issue when I am trying to build the solution...
Hello,
I am trying to fabricate a board based on the Thingy design, including the accelerometer.
I positioned the components, traces, vias and pads following some...
hello Nordic Team
I am using 2 DK
One with Light Switch Proxy Client
Another with Light Switch Proxy Switch
I am using Mobile Mesh App 1.0
Client Provisioning I...
I have been trying to use the nRF Connect app on my Apple iPhone in order to get the Current Time Service.
I bought a Arduino Primo that has an nRF52 on it.
The example...
I am working with an nRF51822 IC revision 2 chip and S110 SD 6.2.1 with Keil 5.10. My version of Keil 5.10 will not recognize the chip. I think that this is because I cannot...
Hi,
I am using nRF52832 microcontroller in project.
I use SPI interface for serial EEPROM.
I could able to see write packets are getting transmitted and verified the...
Hey, I use the Interactive mesh provisioning and configuration tutorial to setup one server and several clients which can communicate with this server.
Can you say me, how...
I have TIMER1 configured as 16-bits wide with no prescaler (62.5ns tick) and CC[2] set up for a varying value near 65535. My work is based on the Nordic blog post about synchronizing...
When I use uart to transfer data, sometimes I get error NRF_ERROR_SVC_HANDLER_MISSING in APP_UART_COMMUNICATION_ERROR when I start sending data. Sometimes this error occurs...
Hey, can I use a complex structure (for example byte array ) as a message parameter instead of one byte like it is done in http://infocenter.nordicsemi.com/index.jsp?topic...
I have a Thread network setup using nRF52840 as per the documentation below, using the Raspberry Pi image provided by Nordic. http://infocenter.nordicsemi.com/topic/com.nordic...
Hi,
In my develop environment , there have many proprietary device. One device is working on PTX mode, and the other devices is working in PRX mode.
If the PTX device...
Hi,
In the FICR (INFO.VARIANT) register on the nRF52832 soldered on my board I can read: AAB0 and in the same register on the NORDIC DK I can read AAE0.
The only different...
Hi,
as described here https://devzone.nordicsemi.com/f/nordic-q-a/37056/supervision-timeout-and-unplanned-disconnect our device has a hard current limit of 2mA.
Problem...
