I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi Nordic,
I've try many times but no luck, I have a PCA10028, which works fine with SDK8~10 and S110.
Recently I found the SDK has become ver11 and SD turn to S130. So...
What is the best method for sending long data to ble_app_uart from android? We tried sending data by breaking into 20 bytes chunks and used thread.sleep() between each packet...
When I'm using the SDK 6.1.0, the twi drivers works while and I can easily understand the twi work flue. Howeve, the SDK 11.0.0 changed the twi drivers. I don't know what...
Hi Nordic,
I am using PCA10000 v2.2.0 with MCP and FW "MEFW nRF51822 0.11.0"
I just tried the "nRF Connect" under Windows 10 and fail to use it. Below is my steps:
...
Hi All,
I'm using nrf52 PCA10040 v 0.9.0, with SDK11. No softdevice being used in this case.
While exploring using EasyDMA with the SPI peripheral, the example in sdk11...
Hi there,
this problem may extend the scope, as it relates the SPI slave device (atmel winc1500). When I run the SPI master example, I can see the data transmitted on oscilloscope...
Hi, I use S110 v8 in my application with DFU support. When DFU is triggered from application (by writing 0x0104 to DFU service control characteristic), then application fails...
Working on a project i want to update the nordic application (firmware) from other MCU, i am having some problem to compute the crc.
How to we calculate the crc of...
When I plug the nRF51822EK (PCA10024) in via USB while holding the reset button down, it mounts as "MBED LOADER" rather than "MBED". This page
developer.mbed.org/.../ ...
Hi,
I have a nordic chip (nrf2832) and I am trying to use it as a LWM2M client and register it to a LWM2M Server. I want to achieve this:
developer.nordicsemi.com/.....
I'm trying to update my SoftDevice with a bootloader, which is basically the same as the one in nRF5_SDK_11.0.0_89a8197. The image is saved in bank 0 and is validated by dfu_sd_image_validate...
This is my first DFU project, and so this may be super-obvious to all of you.
I am writing this here to help others, because it appears that there are others out there...
I have an mBed application that uses the S130 SoftDevice and polls data from a couple of other connected peripherals via I2C & SPI.
I use a Ticker object, which seems to...
Hello,
I use the example dfu_dual_bank_ble_132 in the nrf5x sdk 11 (PCA10040).
I have had my programe before the OTA, i will have a programme wich would update at any...
