I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I am considering software that uses nRF52840, where one side will send advertisements and the other side will scan and obtain data from advertisements.
I am considering...
Hi,
I’m developing a BLE IoT product using the nRF52840 DK, where I need to send a payload of 60 bytes. In a previous response to one of my questions, I was advised to increase...
I have a requirement for PMIC which should include charging, sleep mode integration and should give simultaneously 2 outputs. One output should range from 3-5V the other one...
Hey
I have tried to enable and test coredump as shown in this example: https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-2-debugging/topic...
My production board doesn't support UART, but we have SEEGER JLINK using RTT to debug with. I'm using nRF5_SDK_17.0.2_d674dde\examples\dtm\direct_test_mode project.
If I...
Hello.
I am experimenting with the nRF52-DK board. The tool is segger studio on win x64. Bluetooth appears on the smartphone and disappears after a while. It is not connecting...
Hello,
On my custom board, I need to offload data from my NRF52840 chip via Bluetooth/BLE to my PC for processing. (Ideally using python to receive) Is this formally covered...
We're evaluating RSP with 1oT, and we managed to successfully swap the carrier using RSP with our nRF9160DK, running our standard application.
The nRF9161-DK, running the...
Hello,
i'm developing a custom board with nPM1300 + nrf5340. First things first, i purchased a nPM1300-EK to acquire the needed knowledge to make things working. Unfortunately...
Hi,
I have one nrf52840 board and one bosch BMA456 Shuttle board 3.0 flyer.
I am using zephyr-sdk-0.16.8.
zephyr build and flashing works fine, but when I use device...
Hello,
I am developing a solution based on nrf52-DK, using nRF52840. I have a .hex file produced by the R&D team So far I can flash successfully the board with :
drag...
Hi all,
Recently I am trying to start a secure MQTT connect between Rabbit MQ broker and nRF-9160 or nRF-9151.
nRF9160 is running Serial LTE Modem(SLM) application with...
I've been spending a long time trying to write a driver for the ILI9341 8080 8bit bus interface but all I can't seem to get the display to do anything at all. I'm just seeing...
