I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
I'd like to develop a BLE OTA Bootloader using the NRF Connect SDK, but I need to program my NRF52840 with a Serial Wire debugger. What tools do I need? Is there...
Hey,
Im have a thingy91 and multiple nrf52840 pcbs.
my goal is to make the thing91 a central device that reads data from the nrf52 devices and sends it over to the cloud...
We have a custom board with an nRF7002 controlled by a non-Nordic MCU. The WiFi drivers were ported from SDK 2.7.0, and WiFi in general is working, this question is about...
(I am a beginner) Hello, I recently got the Nordic nRF52840 dongle so I can sniff BLE packets from some devices I have. I set up the dongle following the recommended setup...
Hi,
What is the voltage on nRF52811-CAA chip DCC pin (A5)?
Can the regulated voltage on this pin be used as a voltage source to supply some external circuits?
Please...
Hi,
I am using nRF52811-CAAA bare chip on a standard 2 layer FR4 board and want to design a PCB trace antenna for it to achieve overall x100-200m range.
Is there an example...
Hello everyone,
we are currently designing a PCB based on the nRF52840. The system is dependent on high accurracy of HFXO.
In an old blog post on the TI forum I found...
Hello expert. My computer is windows11 system, using ncs+vscode for development, Jlink software version is V8.10c. My development board is nRF52840(PCA10056). The problem...
I appear to be running into an issue whereby I cannot see my device connected in VS Code using the nRF Connect for VS Code extension.
I have followed all the steps to set...
Hi nordic,
I have successfully completed the Bluetooth over-the-air upgrade using the secure bootloader example. However, we need to add an additional upgrade method. In...
I am trying to add s2opc to my project. But everytime i try to open the complete Workspace in VSCode, the nrf Connect extension, just does nothing. How to reproduce. Take...
I'm thinking of incorporating a TWI slave with nRF52832.
I'm using SDK 17.0.2.
I want to set up a register and read/write multiple bytes with TWI, but I don't know how...
Hi all, My project uses nRF52840 microcontroller and nRF5_SDK_17.1.0. My project uses AT25SF161B flash memory and The little filesystem to store data and everything works...
Hello everyone,
I'm currently working on a project involving the nRF52832 microcontroller and the MAX98357A amplifier for audio playback from an SD card. However, I'm encountering...
