I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I have read some of the Asset Tracker documentation and noticed there is a nice implementation for operating LEDs in the UI module. This seems straightforward for GPIO control...
Hi,
We're having a problem that our application will hang when using the 32 kHz RC oscillator in the mcuboot bootloader and the Zephyr application. We encountered this...
hit there,
i am trying to work with the NRF5 SDK ARMGCC, in the IDE options a ARMGCC folder exists with an .ld file and makefile. i run the make and get the following error...
Hi,
I'm aiming to develop a custom two-wire serial interface (TX, RX). To achieve this, I'm planning to implement output capture for TX and use GPIO interrupts for RX. For...
NCS v2.7.0 and sysbuild system.
I'm looking for some clarification about Secure Boot and implementing a custom signing command.
What is the difference between secure boot...
software: ncs 2.5.0, zephyr/samples/subsys/fs/fs_sample
hardware: nRF52840 (not DK, designed by customer) and nRF52832 (not DK, designed by customer)
Step1: build within...
Hello everyone
I'm trying to build an app using Segger Embedded Studio and a nRF52832. I'm currently struggling to include the fds module since i get the following errors...
Hello,
We would like to program the external flash connected to the nRF5340 via SWD during manufacturing.
Is this possible? Do you have any documentation that explains...
Hi
When doing a Software reset the RAM contents are persisted, however when doing a Hardware reset via nREST pin on the module then the non-initialized RAM section is...
Hi,
I am designing the ARGO module http://wizcube.eu/argo.html . I am using the excellent KiCAD library https://github.com/hlord2000/nordic-lib-kicad
It seems there is...
Hi, I'm developing a product for a client using nrf52840 which has support for DFU OTA over BLE. I'm using nrf connect sdk 2.5.0 and DFU OTA over BLE was ridiculously easy...
We're using a nRF5340 module on our board, and have basically everything working as we'd like using SDK 2.1.0.
I've tried updating to SDK 2.6.1, and managed to resolve all...
Hi,
In our new project, we are using the nRF5340 WLCSP package and configuring the system ON - low-power mode in our application code. We measured the current consumption...
Hi,
Ubuntu 20.3
vscode + nrf connect extension
when i create new application from exsample project broadcast_audio_source for nrf5340, after build, and flash into the...
