Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hi,
I am trying to connect the current product with MCU EFM32GG290F1024 to a Nordic BLE module in a serialization over UART.
I have port the SDK to my project and need...
1. hardware : nRf52840 dongle.
2. Purpose : Update Firmware into dongle to be sniffer, and restore original default manufacturer firmware for nRF Connect v2.6.0 desktop...
Hello All,
i my project there are 2 ble services now i want to add Flash read/write application i tried with fds as well as flash_write example from the SDK 15.3.0
i added...
Hello!
Apologies in advance for my english.
I already asked a similar question, here is the link to it
When trying to connect a PWM driver PCA9685, I ran into problems...
Hello.
We are using NRF52840, SDK 16.0.0 and SoftDevice S140 7.3.0 and are noticing irregular SoftDevice asserts that don't seem to be triggered by any one particular function...
Hello,
I am curious to see if it is possible to register a device through a web app using the nRF52840's NFC. The goal is to scan the NFC on the device, enter the personal...
Hello,
I'm working on a custom board with a nRF52833.
A small external battery is on the board, and when the power is off, 32.768khz of low power remains on the battery...
I'm running the SDK 17 radio test example on two nRF52840 DKs. My goal is to do a PER measurement in 802.15.4 -mode.
I configure the boards to use ieee802154_250Kbit mode...
Hi, I am using nrf52832 board. I was trying to disable the GPIOTE interrupt for a particular event (Event4) using INTENCLR register. My code was NRF_GPIOTE->INTENCLR = 1 ...
I am trying to get the nRF9160 DK power consumption down as much as possible to establish a baseline for development. After struggling to achieve the values claimed in the...
Hello,
I am using NCS v1.5.0 and an nRF9160 on a custom board, my application has a custom SPM and the secondary slot for the firmware image upgrade is stored on an external...
Hi,
I'm developing a peripheral sensor and central receiver as a complete set. So I wish the peripheral is only visible(or connectable) to its central device.
I know the...
Hi there!
I wanted to do a little side project that's something completely different than BLE Mesh (which I do for work). I decided Zigbee would be fun. Even more so because...
Hi,
I have an nRF52840 DevKit and dongle and am using SDK for mesh v.5 with SDK 17.0.2.
I want to update the firmware in a mesh network and am working on the mesh DFU...
