I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
HI,
I wanted to know what is the default tx power set level in S130, I took a example from sdk 11.0.0, (ble Peripheral/ble_app_uart) but i dont see anywhere this example...
I struggled for a while with this: the SDK documentation and the example application did not explain a common use case: reading and writing single-byte registers in a peripheral...
I need to measure periods with high precision, so I need to make sure that the HF clock is using the external XTAL; when the softdevice is not started (for testing mode) I...
Hello,
I am building a wireless sensor network for my coffee business, I am using a raspberry pi as the gateway with nrf24l01 connected to it, I have a bunch of sensor nodes...
HI
I have followed the below-mentioned tutorial
https://devzone.nordicsemi.com/nordic/b/archives/posts/nrf-connect-sdk-tutorial---part-2-ncs-v1-4-0#h117sk6474thpzmbdphj6gan2vw7rzj...
PCB above my collection of audio data by codec, and then through the Bluetooth upload, the audio signal noise will be ticking ticking, may I ask what is the reason
hi, all
I added scan module at 'ble_app_uart' example..
Error in function nus_c_init. (0x08)
So when I follow the line by line, it seems that the 'registered_handler_set...
Hi,
Iam using Segger Embedded Studio (SES) v5.20, SDKv17.0.2, NRF52840 DK board, NRF52810 Microcontroller in the Custom Board
Since we don't have the PCA10040e folder...
Hello Everyone,
We are using nRF52840 IC for our products which has 1 MB of flash.
Thread Secure DFU Example provided with Nordic SDK supports only Dual Bank DFU. This...
Hi,
I'm working in the asset tracker v2 project and currently I need to do a simple hex to char array conversion. This entails using sscanf. However the use of sscanf consistently...
Hi, I am trying to expand on the ESB PRX example and want to recreate functions with the same functionality as Arduino's micros() and millis() functions. I'd like the following...
Hello, Nordic & all:
I have a problem when use P0.21 as the libuarte's uart RX( base on libuarte example/sdk17.0.2) for my custom nrf52840 board， I looked up the reference...
We just received a PPK2 and have used it in several configurations to test a custom nrf52832 board that runs on a 3v lithium coin cell.
When connected in the following manner...
Hello:
I am working on an application that uses a simple UDP socket for transmitting data. I would like understand the zephyr BSD socket behavior when there are cellular...
