Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using NRF5340DK, and I want to define P0.20 as my SPI MOSI pin.
However, this pin is pre-defined by Zephyr as uart0 tx pin, in zephyr.dts:
Everytime I reset...
Hello,
Our product has two pieces of information that must be programmed during production: a shared secret key (128 bits) and a public, unique device identifier, also 128...
Hi guys:
I flashed the ble_app_uart(SDK-location\nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart.),
When I pressed button1, there...
Dear all,
I'm trying to modify ble_central_uart (SDK16) to connect two peripherals. I've achieved the connection and been able to print receiving data via UART.
But...
Hi All,
I am NEW to Nordic Devices and I want to try to learn as much as I can.
I have bought a startup Dev Board to learn my skills with: E104-BT5032A-TB E104-BT5032A...
Hi guys.
I wonder the program run start from which section and how to enter the app when 52840 poweron? Start from SofeDevice?
I only flashed ble_app_uart and SoftDevice...
Hi all,
I'm trying to transfer my custom project pca10056 (which is to broadcast a beacon) to nRF52811 hardware and I'm facing some issues in the last stage of build.
...
HI ,
My environment:
nrf connect sdk
nrf5340 dk
segger studio ide.
could you please provide me timer example code for nrf5340 board.
Thanks & Regards,
...
Hi,
I am using an NRF 51422 DK, SDK 12.3, and Soft Device S130. I am also a beginner to development with Nordic Products, and RSSI collection in general. I am using the...
SDK: 17.0.2
IDE: SES
nRF52832 module
Hi!
I have a nRF52832 based custom board operating on battery power. I assigned a variable to the non_init section in SES and...
Hey!
I have an isp1807 test board, which uses an nrf52840 chip, and an isp1p807 programmer (ISP130603E). Currently, my code is written using the nrf52 sdk v17. When I am...
Hi, I'm using nRF9160 as host and nRF52833 as a controller with NCS 1.5.0 SDK. On nRF52833 LPUART sample runs, I have added needed configurations for extended advertising...
Dear All,
I am working on interfacing BME680 with nRF52840-DK board. I got the output for Temperature, Pressure and Humidity but not getting the output for Gas resistance...
What should be considered for choosing a chipset? the followings are in my mind. Could you please tell me if I am correct and if I should consider anything else too.
1)...
