I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
Recently we have bought nRF9160 DK PCA10090 devices and tried to add to nrf cloud account but we end up with issues.
Following the standard procedure mentioned in...
Hello,
I noticed that when my Thingy is charging the Temperature measured is 4°C higher
The data are coming from NRF Cloud.
We can clearly see the temperature rising...
I use SDK16.0.0 and SD7.0.1-S132 Implement NUS functions, 1 * ble_central and 6 * ble_peripheral. The uart of ble_central connect to STM32MCU. My system run as follows, 6...
Hi. I tried to add rel_humidity_measurement cluster to multisensor example. New cluster is visible , but i cant get humidity data report I used cli exemple, here are logs...
Hello,
We have studied the getting started guide for the OTA upgrade at the link below.
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development...
Hi all,
I was trying to evaluate the nRF52840 current consumption through the online power profiler. I set the tool as in the below image
there are three standby currents...
Hello guys,
I am attempting to send AT commands to an nrf9160 over UART. I started by loading the serial_lte_modem sample and sending commands using the LTE link monitor...
If I add
CONFIG_BT=y
CONFIG_BT_PERIPHERAL=y
to tests/crypto/prj.conf then CONFIG_ENTROPY_CC310=y gets turned off when building. By default, this will then cause a hard...
Hi
I am using the nrf52832 with the heart rate (freertos) example
Let say i want to add a new service and characteristic to that service ,this service is not suppose to...
Hi,
I have developed a simple system based around a Raspberry Pi Zero. The system uses a couple of sensors to measure temperature and water pressure using a ADS51115 A/D...
Hello,
I use NRF Connect Desktop on Windows 10 - 64 bits.
When I lauch the Programmer application with my NRF52 I have this issue :
2020-07-20T11:27:17.148Z ERROR Error...
Hi,
I am using the nRF5_SDK_13.1.0_7ca7556.
When I call the pm_conn_secure(), it returns NRF_ERROR_INTERNAL.
Can you tell me why did the NRF_ERROR_INTERNAL occur?
...
Hi ,
I followed the getting started steps and enabled the global sim. Now the LED 3 is blinking .
In the LTE Link Monitor , I see the following :
2020-07-22T03...
When I enable watchdog in main application by:
nrf_drv_wdt_config_t config = NRF_DRV_WDT_DEAFULT_CONFIG; err_code = nrf_drv_wdt_init(&config, wdt_event_handler); APP_ERROR_CHECK...
