I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
I'm trying to understand which part of the code provides the bluetooth connection between two nRF52840. I worked in sdk15.0.0 with multilink, blinky and uart examples to solve...
Hi, everyone,
We are developing project with nRF52832 chip.
For making it's monitoring we used UART communication port. But on the next step of development we had to enable...
I need to interface an nRF52832 with ADS7042, hence the following questions:
1) as ADS7042 requires 14 clock cycles per read cycle, is the nRF52832 SPI API applicable in...
I am constantly receiving an NRF_FAULT_ID_SD_ASSERT error within a non-deterministic time after connecting via BLE.
The program Counter is always 75936 and Info == 0. I...
Hi
Development Environment : windows 7- keil ARM SDK 5 - Arm Debugger Programmer(Waveshare) - nRF51822 EVK from Waveshare
What is the boot_PIN or Boot_Mode PIN
I want...
I am wanting to increase the length of one of my characteristics used when my device is acting as a peripheral. When I increase the size of my characteristic, the softdevice...
Hi,
I needed some figure for my controller selection,
Please if can you tell tthe exact answer it will be very help full,
Using NRF serial example for uart with baud...
Hello,
I have a voltage divider/thermistor circuit where R1 is an NTC thermistor of 100kOhm at 25 ° C. R2 is 100kOhm right now.
I took peripheral_saadc example for SDK15...
Hi all,
I'm testing out and adapting the Thingy Mesh Demo v0.1 , which uses nRF SDK for Mesh v1.0.1 for my internship. I will be testing out a Thingy's Mesh network for...
Hi,
I tried, ble_blinky example on DK, it works well. Also advertising interval 40ms on nrfconnect mobile app,this is consistent with SDK.
Now, i try same example with...
Hello
My name Ilya, am from global company Rosslare -access control. i am a R&D lieder.
I have found that nRF52840 is accepted to my new project - BLE reader.
I want...
Chapter "18.6.1 Power-on reset" of the data sheet describes " A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply...
Hi,
I'm using the BDS Plugin to generate code and I noticed that the code generated for adopted services it's totally different compared to the code into nRF5_SDK_14.2.0_17b948a...
I am trying to use the watchdog interrupt on an NRF52832 but am unable to get it to fire; the watchdog fires, but as far as I can tell not the preceding interrupt. Here is...
