Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hello,
I have a custom board with an nRF52833 and a W25Q512JVEIQ, which communicate over SPI (not QSPI). I successfully accessed the W25Q512JVEIQ (executed my own read and...
Hi, I am using nRF52832 module BL652. I want to measure the battery voltages of a 9V battery. What are the best possible resistors value to measure voltage of such battery...
Hello, We have a custom PCB with both the nRF9160 and nRF52832. Currently, the nRF52 functions as an HCI controller connected via LPUART to the nRF9160. We're at the stage...
Dear sir:
When I first use CHIP tool in my Ubuntu NB, I can commission bulb(52840) through OTBR(Pi4+52840 RCP) successfully, besides, I can use CHIP tool to control bulb...
Hello,
I am currently checking the RSSI measurement precision, and we got very large errors (up to 10dB error) on the RSSI vs input power.
To avoid any PCB / matching...
I'm new to nRF5340 development, and I'm reviewing partitioning for multi-image DFU. I've enabled the bootloader with CONFIG_BOOTLOADER_MCUBOOT=y , and after checking partitions...
Hey,
I am having an issue where my device doesn't show up in the Nrf Connect app as "connectable" despite as far as I can tell being set as a connectable device. This doesn...
Hello,
I'm trying to upload code to an external board using an NRF52dk, and am having an error in vscode as shown below.
My issue seems to be very similar to the one...
Hello.
I understand that Radio Notifications is an API that notifies you before and after scheduled radio events occur within a SoftDevice, but can you tell me more about...
Good day
I have the NRF_desktop keyboard application running on the NRF52840 Dongle, Zephyr 2.6.1. I would like to us the nrf52840 ProMicro as it has a battery charger build...
Hi,
I would like to know Number of UARTs available for Murata 2AB. According to the 2AB datasheet, there is one UART, but the nRF52340 datasheet shows two UARTs. Can 2AB...
HI,
I am building "esb_ptx" sample in NRF54L15-PDK, by using CONFIG_DYNAMIC_INTERRUPTS, but it;s always reset like below;How to config the prj.conf to enable CONFIG_DYNAMIC_INTERRUPTS...
Dear all:
I found that the nrf52840 flash size is only 1MB, but the size of light bulb load is about 850KB, I have some questions:
1. Does it contains the FOTA region...
Hi
I am trying to use nrf52811 using nrf52840 DK board.
First, I check simple GPIO example working on my nrf52811 based custom boards
Second, I checked the Bluetooth...
How can I execute a command to commission a device for Thread by using the QR code or pairing code? (without using the pin_code or discriminator) Thanks.
