Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hello everyone, I took the example code "ble_app_hrs" and added a pin toggle to verify that the code is loaded correctly onto my custom board, which is programmed via the...
I'm trying to install the toolchain manager on a new work computer and I'm running into issues that I think are related to my work's proxy.
I've tried following the steps...
I am trying to configure the STS4x temperature sensor by Sensirion on I2C on a nRF5340DK, I have setup my the coding exactly how sensirion suggested except few changes such...
Hi,
When I try nrfsdk/zephyr/sample/bluetooth/periodic_adv_conn. I notice that the max subevent data size is about 64bytes. If I send a data size larger, I will get a error...
Hi DevZone,
I have made a custom PCB with the nRF52832. I placed the same coaxial connector that is on the nRF52 DK in my PCB. At this point, I want to test the BLE functionalities...
Hi,
I am unable to build the MQTT over Wi-Fi lesson 4, exercise 1 using the nrf7002dk_nrf5340_cpuapp board configuration, but the same code builds successfully with nrf7002dk_nrf5340_cpuapp_ns...
Greetings all, Does the Direct Test Mode (DTM) app v2.4.1 provided in the NRF Connect for Desktop v5.0.2 package support gain settings for the nRF21540 FEM such as +10, or...
I am working on nrf52840 and I want to control the motor speed so I want to generate the variable frequency PWM for the same. How can I generate the variable frequency PWM...
Hello,
I need to configure second UART for nRF52840 DK. So I would like to know the overlay file for uart2 configuration with exact GPIO pins. Also the .c file to initialize...
I 'm porting code from Zepyr 3 .5 to 3 .7 and am having errors in my ds2484 1 -wire device . It was working fine but now reports an init error unless I add deferred -init...
L.S.,
I'm trying to build an "Arduino" port for the nrf52840 (Seeed board).
When building an example I'm getting the following errors during the link phase:
.\Objects...
Hello,
In my project I have b0, mcuboot and an app. My nRF SDK version is v2.7.0.
My project works fine if I use an absolute address in SB_CONFIG_BOOT_SIGNATURE_KEY_FILE...
Hi,
I am working with the nrf9160 and ncs2.7. Is it possible to programmatically change how pins are defined? For example, on startup 2 pins are for I2C (SCL and SDA) and...
