Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hardware: nRF9151DK OS: Windows 11 Toolchain: nRF Connect SDK v3.1.99 (Toolchain v3.1.1) Debugger: Onboard J-Link (Interface MCU)
Description of the Issue: I am facing a...
Hi all,
I’m developing firmware using USB CDC with UART async API to transmit data at about 102 kB/s . However, during uart_tx() calls, I often get a -16 error (EBUSY)....
I am using the nRF54L15 with SDK 3.0.0 and developing using npm2100_fuel_gauge for the nPM2100.
I see the battery model for the CR series only includes CR2032, but I...
Hi there.
I am currently working on WIFI provisioning using BLE using nRF7002 and nRF5340.
The CPU structure of my custom board is based on the nRF7002DK. So I am testing...
Hello,
My first attempt with channel sounding.
Hardware Setup:
- Initiator: nRF54L15 DK running `channel_sounding_ras_initiator` sample (no issues found so far) - Reflector...
nRF9160, mfw 1.3.7, NCS 2.9.2
Case:
The modem first connects to LTE-M (Germany, band 3), pretty well.
Then the modem is moved into a building basement (band 8 or 20...
Hi Team,
We are using nRF54L15.
1. Is there any api to read BLE MAC address?. If yes, can please provide it?
2. What are the configurations need to make 'yes' in ...
Whenever I open my workspace or build in VS Code, the Output tab of the bottom pane opens to nRF Connect output where it repeats this many times:
How can I debug this...
Hello.
We're planning on using a MIPI Antenna Tuner in our upcoming design and I'm referencing the documentation here for the PHASE ON (1) portion
https://docs.nordicsemi...
According to the nRF9151_PS_v1.1 specification, when using PSM, the current consumption should be below 5 µA ("LTE power saving mode (PSM) floor current – 2.7 µA").
However...
I am working with the Radio Test sample, but the project does not include any .overlay file by default. I created my own .overlay file and placed it inside the boards/ directory...
Is the schematics developed by our engineer for the antenna okay?
1. Is the L6 and 0 ohm resistors are for tuning?
2. Can I remove the 0 ohm resistor and use the same...
Modem Firmware: mfw_nrf91x1_2.0.3
SDK Version: 3.1.1
nrf9151
Using the aws_iot sample as a reference, I'm trying to get my device to connect to an IoT instance that...
Hi
my customers are complaining that they have a bad connection in a large conference hall with many people.
Actually the other people in that huge room are not using...
Hi,
We are observing cellular positioning timeouts. A-GNSS is enabled and the device is provisioned in nrfcloud.
The device is located indoors, thus GNSS based positioning...
