Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello Guys,
I'm developping and st7789 IPS screen driver and i'm having problem with SPI0 . I'm using NRF52840 DK 2.0.1
First I took SPI example from sdk 17.0.2 configured...
Hello All,
I am using SES on BMD340 controller with FreeRTOS project.
After few modification in the code, I am facing *.elf doesn't exist during linking stage. There...
On a nRF52833 on a custom PCB, due to space and allocation limitations, I need to run UART Rx and UART Tx over GPIO pins that are limited to standard drive, low frequency...
Dear all,
I have a NRF52832 module (EBYTE E73) and before yesterday, everything was fine.
We had a outdoor test last week and till then, everything was fine.
After...
I've tried this with both 1.5.0 and 1.5.1, with the same results. I install the SDKs using the toolchain manager, and when the installation finishes I open a bash shell, also...
I'm learning how to use OTA DFU on Win10 laptop. I followed this and this guide step by step. I have a couple of questions:
1) (See below code) How to use " arm-none-eabi...
I've recently purchased a Thingy:91 and wasn't able to update its firmware via nRF Connect. I'm guessing this is because that there is no MCUboot on the Thingy:91 that I have...
Have a USB powered Chengdu Ebyte nRF52840 Dongle (PCA100059-style) that has the following:
- USB 5V
- VBUS pin : connected directly to USB 5V
- VDD pin: not connected...
Hello Nordic!
I've been implementing some more commands in my endpoint handler but (I don't know how) it has stopped working. I have added the responses of the commands...
I'm getting started with an (older) nrf52840DK board. I'm following the instructions presented here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hello,
I'd like to test the condition when the LTE-M network is unreachable on the nrf9160dk. I have interrupted the antenna path by connecting a 50ohm termination to J1...
I designed a prototype custom board with the nrf52840 (QIAAD0).
It has a USB socket, with an external LDO supplying 3.3V to VDDH + VDD (following the recommended circuit...
Hi,
I am working on an SPI DFU on my NRF52840 DK using SDK 15.2.0. So far the init packet is able to transfer, however, after I create an object for transferring the firmware...
Dear community,
I compiled the ble_app_hids_mouse example from SDK 17.0.2. From the datasheet of BM833A, i can read:
Flash/RAM: 192KB/24KB
Compiling the project unmodified...
